Code:
CPU 01
BCM74390011
PRID07251111
v1.7
RR:00000003
BFW
SEC
seclib-1.5
BBL v1.0.1
AVS init...
spare0/rmon_hz=017f7672
spare1/rmon_vt=017f7572
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
AVS: OTP Decrypt 0x00000000, OTP Verify AVS 0x00000000
LOADED
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MemsysFW: OTP Decrypt 0x00000000, OTP Secure Boot 0x00000000
SHMOO 01020000 BLD:9695 HW:hpf0_b1p6 V:1.2.0.0
MCB: FIX
AVS start:status=000000ff
STB: Current voltage=0000039c(924)
temperature=00009822(38946)
PV=00000358(856)
MV=0000039c(924)
AVS FW rev=30333078 [0.3.0.x]
OK
DDR0: *@ ffe0ba98 <= ffe0ba98 MEMSYS-0 @ f1100000 OK
DDR1: -
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
OTP SSBL Encrypt 0x00000000
OTP Sec Boot 0x00000000
OTP read MichEn 0x00000000
MICH: disable success
SSBL
no v092_to_v095 conversion is performed
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 0704cff0
_ebss 0704eab8
_end 0704ead8
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0704cff0 to 0704eab8 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.07 v1.07-r27 hd51
.'__ ,' (2019-05-15 )
/,' Copyright (C) 2019 Broadcom Corporation
/'
Board: BCM97251SSV
SYS_CTRL: product=72511, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822080e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) memsys_1_disable(0x00008000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000461: moca2_disable(0x00000001) pcie1_disable(0x00000040) rfm_disable(0x00000020) sata1_disable(0x00000400)
CPU: 2x A15, 1719 MHz
SCB: 432 MHz
DDR0 @ 1061MHz, DDR1 N/A
CS0: SFDP SPI, 8MB, 64kB blocks, 256B pages
CS1: NAND: unrecognized ID: 0xffffffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.919V, T=+39.433C, PV=0.856V, MV=0.924V, FW=30333078 [0.3.0.x]
USB otp=00000040
board selection update!
board was ?, now a (flags:0xffe00000)
Loader:zimg Filesys:raw Dev:emmcflash0.linuxkernel File:(null) Options:root=/dev/mmcblk0p3 rootsubdir=linuxrootfs1 kernel=/dev/mmcblk0p2 rw rootwait hd51_4.boxmode=1
Reading 4782416 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x761c000)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.10.12 (oe-user@oe-host) (gcc version 9.2.0 (GCC) ) #1 SMP Sun Oct 31 17:58:38 UTC 2021
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: BCM97251SSV
[ 0.000000] cma: Reserved 440 MiB at 0x0000000014800000
[ 0.000000] cma: Reserved 192 MiB at 0x0000000030000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 14 pages/cpu @d3ddd000 s26764 r8192 d22388 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: root=/dev/mmcblk0p3 rootsubdir=linuxrootfs1 kernel=/dev/mmcblk0p2 rw rootwait hd51_4.boxmode=1 brcm_cma=440M@328M brcm_cma=192M@768M console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 380524K/1048576K available (6675K kernel code, 365K rwdata, 1844K rodata, 352K init, 215K bss, 20884K reserved, 647168K cma-reserved, 65536K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc068d2e8 (6677 kB)
[ 0.000000] .init : 0xc088a000 - 0xc08e2000 ( 352 kB)
[ 0.000000] .data : 0xc08e2000 - 0xc093d790 ( 366 kB)
[ 0.000000] .bss : 0xc093f000 - 0xc0974ff4 ( 216 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0805000, parent irq: 16)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0807000, parent irq: 17)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0809640, parent irq: 18)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf080b200, parent irq: 19)
[ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2)
[ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xf080d380, parent IRQ(s): 3)
[ 0.000000] brcmstb: biuctrl: MCP: Write pairing already disabled
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[ 0.000004] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[ 0.000012] Switching to timer-based delay loop, resolution 37ns
[ 0.000291] Console: colour dummy device 80x30
[ 0.000313] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000324] pid_max: default: 32768 minimum: 301
[ 0.000430] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000436] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000894] CPU: Testing write buffer coherency: ok
[ 0.001147] CPU0: update cpu_capacity 1024
[ 0.001154] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001372] Setting up static identity map for 0x8440 - 0x8498
[ 0.003677] smp: Bringing up secondary CPUs ...
[ 0.004401] CPU1: update cpu_capacity 1024
[ 0.004404] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004466] smp: Brought up 1 node, 2 CPUs
[ 0.004476] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[ 0.004481] CPU: All CPU(s) started in SVC mode.
[ 0.004884] devtmpfs: initialized
[ 0.011186] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.011384] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.011401] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.025789] NET: Registered protocol family 16
[ 0.026207] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.031399] cpuidle: using governor ladder
[ 0.035655] cpuidle: using governor menu
[ 0.044797] No ATAGs?
[ 0.044887] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.044895] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.059665] SCSI subsystem initialized
[ 0.060856] usbcore: registered new interface driver usbfs
[ 0.060923] usbcore: registered new interface driver hub
[ 0.060971] usbcore: registered new device driver usb
[ 0.061032] Linux cec interface: v0.10
[ 0.061079] Linux video capture interface: v2.00
[ 0.061144] pps_core: LinuxPPS API ver. 1 registered
[ 0.061150] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.061170] PTP clock support registered
[ 0.061656] Advanced Linux Sound Architecture Driver Initialized.
[ 0.062410] clocksource: Switched to clocksource arch_sys_counter
[ 0.062618] FS-Cache: Loaded
[ 0.068681] NET: Registered protocol family 2
[ 0.069047] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.069088] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.069161] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.069248] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.069274] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.069409] NET: Registered protocol family 1
[ 0.069781] RPC: Registered named UNIX socket transport module.
[ 0.069785] RPC: Registered udp transport module.
[ 0.069789] RPC: Registered tcp transport module.
[ 0.069792] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.070962] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 0.072288] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.072779] FS-Cache: Netfs 'nfs' registered for caching
[ 0.072911] NFS: Registering the id_resolver key type
[ 0.072932] Key type id_resolver registered
[ 0.072937] Key type id_legacy registered
[ 0.072947] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.072953] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.073087] FS-Cache: Netfs 'cifs' registered for caching
[ 0.073135] Key type cifs.spnego registered
[ 0.073267] fuse init (API version 7.26)
[ 0.075265] bounce: pool size: 64 pages
[ 0.075318] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.075327] io scheduler noop registered
[ 0.075333] io scheduler deadline registered
[ 0.075362] io scheduler cfq registered (default)
[ 0.075757] brcm-gisb-arb f0400000.gisb-arb: registered mem: f0a09000, irqs: 47, 48
[ 0.076068] brcm-sata-phy f0458100.sata-phy: registered 1 port(s)
[ 0.076511] brcm-cma brcm-cma.0: Initialized Broadcom CMA root device
[ 0.077144] brcm-cma brcm-cma.0: Added CMA device @ PA=0x14800000 LEN=0x1b800000
[ 0.077709] brcm-cma brcm-cma.1: Added CMA device @ PA=0x30000000 LEN=0xc000000
[ 0.111671] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.113169] console [ttyS0] disabled
[ 0.113209] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 34, base_baud = 5062500) is a 16550A
[ 0.813649] console [ttyS0] enabled
[ 0.817726] f040a940.serial: ttyS1 at MMIO 0xf040a940 (irq = 35, base_baud = 5062500) is a 16550A
[ 0.827059] f040a980.serial: ttyS2 at MMIO 0xf040a980 (irq = 36, base_baud = 5062500) is a 16550A
[ 0.843360] brd: module loaded
[ 0.850220] loop: module loaded
[ 0.854215] OF: /rdb/sata@f045a000/sata-port@0: could not get #phy-cells for /rdb/sata-phy@f0458100
[ 0.863404] brcm-ahci f045a000.sata: masking port_map 0x3 -> 0x1
[ 0.869474] brcm-ahci f045a000.sata: SSS flag set, parallel bus scan disabled
[ 0.886708] brcm-ahci f045a000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x1 impl platform mode
[ 0.895688] brcm-ahci f045a000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 0.904815] scsi host0: brcm-ahci
[ 0.908427] scsi host1: brcm-ahci
[ 0.911918] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 44
[ 0.919854] ata2: DUMMY
[ 0.922314] brcm-ahci f045a000.sata: Broadcom AHCI SATA3 registered
[ 0.929263] libphy: Fixed MDIO Bus: probed
[ 0.933683] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.951404] libphy: bcmgenet MII bus: probed
[ 0.978411] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.984263] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.010192] ehci-brcm: EHCI BRCM driver
[ 1.014154] ehci-brcm f0470300.ehci: EHCI Host Controller
[ 1.019588] ehci-brcm f0470300.ehci: new USB bus registered, assigned bus number 1
[ 1.037293] ehci-brcm f0470300.ehci: irq 147, io mem 0xf0470300
[ 1.047920] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.049409] ehci-brcm f0470300.ehci: USB 2.0 started, EHCI 1.00
[ 1.049960] hub 1-0:1.0: USB hub found
[ 1.049984] hub 1-0:1.0: 1 port detected
[ 1.050271] ehci-brcm f0470500.ehci: EHCI Host Controller
[ 1.050283] ehci-brcm f0470500.ehci: new USB bus registered, assigned bus number 2
[ 1.060393] ehci-brcm f0470500.ehci: irq 148, io mem 0xf0470500
[ 1.067401] ehci-brcm f0470500.ehci: USB 2.0 started, EHCI 1.00
[ 1.067889] hub 2-0:1.0: USB hub found
[ 1.067933] hub 2-0:1.0: 1 port detected
[ 1.068155] ohci-brcm: OHCI BRCM driver
[ 1.068323] ohci-brcm f0470400.ohci: BRCM OHCI controller
[ 1.068338] ohci-brcm f0470400.ohci: new USB bus registered, assigned bus number 3
[ 1.068426] ohci-brcm f0470400.ohci: irq 149, io mem 0xf0470400
[ 1.126824] hub 3-0:1.0: USB hub found
[ 1.130616] hub 3-0:1.0: 1 port detected
[ 1.134796] ohci-brcm f0470600.ohci: BRCM OHCI controller
[ 1.140224] ohci-brcm f0470600.ohci: new USB bus registered, assigned bus number 4
[ 1.147889] ohci-brcm f0470600.ohci: irq 150, io mem 0xf0470600
[ 1.209786] hub 4-0:1.0: USB hub found
[ 1.213567] hub 4-0:1.0: 1 port detected
[ 1.217686] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.224241] ehci-pci: EHCI PCI platform driver
[ 1.228748] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.234947] ohci-pci: OHCI PCI platform driver
[ 1.239751] xhci-hcd f0471000.xhci: xHCI Host Controller
[ 1.245099] xhci-hcd f0471000.xhci: new USB bus registered, assigned bus number 5
[ 1.252797] xhci-hcd f0471000.xhci: hcc params 0x0250f17d hci version 0x100 quirks 0x00010010
[ 1.261366] xhci-hcd f0471000.xhci: irq 151, io mem 0xf0471000
[ 1.267808] hub 5-0:1.0: USB hub found
[ 1.271595] hub 5-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 1.278857] xhci-hcd f0471000.xhci: xHCI Host Controller
[ 1.284193] xhci-hcd f0471000.xhci: new USB bus registered, assigned bus number 6
[ 1.291735] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.300190] hub 6-0:1.0: USB hub found
[ 1.303974] hub 6-0:1.0: 2 ports detected
[ 1.308301] usbcore: registered new interface driver uas
[ 1.313711] usbcore: registered new interface driver usb-storage
[ 1.320019] mousedev: PS/2 mouse device common for all mice
[ 1.325883] i2c /dev entries driver
[ 1.329662] IR NEC protocol handler initialized
[ 1.334215] IR RC5(x/sz) protocol handler initialized
[ 1.339281] IR RC6 protocol handler initialized
[ 1.343823] IR JVC protocol handler initialized
[ 1.348364] IR Sony protocol handler initialized
[ 1.352994] IR SANYO protocol handler initialized
[ 1.357710] IR Sharp protocol handler initialized
[ 1.362426] IR MCE Keyboard/mouse protocol handler initialized
[ 1.368271] IR XMP protocol handler initialized
[ 1.372815] smssdio: Siano SMS1xxx SDIO driver
[ 1.377270] smssdio: Copyright Pierre Ossman
[ 1.381943] sdhci: Secure Digital Host Controller Interface driver
[ 1.388142] sdhci: Copyright(c) Pierre Ossman
[ 1.392511] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.431411] mmc0: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[ 1.438984] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.444581] usbcore: registered new interface driver usbhid
[ 1.450172] usbhid: USB HID core driver
[ 1.454575] NET: Registered protocol family 17
[ 1.459103] Key type dns_resolver registered
[ 1.463501] ThumbEE CPU extension supported.
[ 1.467793] Registering SWP/SWPB emulation handler
[ 1.480154] ALSA device list:
[ 1.483166] No soundcards found.
[ 1.487422] Freeing unused kernel memory: 352K
[ 1.491884] This architecture does not have kernel memory protection.
[ 1.584360] mmc0: new high speed MMC card at address 0001
[ 1.590197] mmcblk0: mmc0:0001 4MEYMA 3.66 GiB
[ 1.594876] mmcblk0boot0: mmc0:0001 4MEYMA partition 1 2.00 MiB
[ 1.600931] mmcblk0boot1: mmc0:0001 4MEYMA partition 2 2.00 MiB
[ 1.607006] mmcblk0rpmb: mmc0:0001 4MEYMA partition 3 128 KiB
[ 1.616885] Alternate GPT is invalid, using primary GPT.
[ 1.622235] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 1.656432] usb 3-1: new full-speed USB device number 2 using ohci-brcm
[ 1.835927] EXT4-fs (mmcblk0p3): recovery complete
[ 1.843075] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 1.855953] random: fast init done
INIT: version 2.88 booting
Starting fake hwclock: loading system time.
Fri Feb 18 19:59:46 UTC 2022
[ 2.070315] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 2.080301] usb 3-1: device not accepting address 2, error -62
[ 2.096683] Adding 262140k swap on /dev/mmcblk0p7. Priority:-1 extents:1 across:262140k SS
[ 2.244463] usb 3-1: new full-speed USB device number 3 using ohci-brcm
[ 2.665421] usb 3-1: device not accepting address 3, error -62
[ 2.715734] hd51_1: module_layout: kernel tainted.
[ 2.720572] Disabling lock debugging due to kernel taint
[ 2.725908] hd51_1: loading out-of-tree module taints kernel.
[ 2.732140] usbcore: registered new interface driver tpm
[ 2.835411] usb 3-1: new full-speed USB device number 4 using ohci-brcm
[ 3.010397] usb 3-1: device descriptor read/64, error -62
[ 3.290400] usb 3-1: device descriptor read/64, error -62
[ 3.565401] usb 3-1: new full-speed USB device number 5 using ohci-brcm
[ 3.740399] usb 3-1: device descriptor read/64, error -62
[ 4.018455] usb 3-1: device descriptor read/64, error -62
[ 4.129511] usb usb3-port1: unable to enumerate USB device
/dev/dvb/adapter0/video0: No such file or directory
[ 4.379733] EXT4-fs (mmcblk0p3): re-mounted. Opts: data=ordered
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1735: No soundcards found...
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
net.ipv4.tcp_timestamps = 0
Starting stb hwclock: loading system time.
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Configuring network interfaces... [ 5.864404] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
[ 5.873733] bcmgenet f0b00000.ethernet: configuring instance for internal PHY
udhcpc: started, v1.31.0
udhcpc: sending discover
udhcpc: sending discover
[ 9.418100] bcmgenet f0b00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
udhcpc: sending discover
udhcpc: sending select for 192.168.100.245
udhcpc: lease of 192.168.100.245 obtained, lease time 14400
/etc/udhcpc.d/50default: Adding DNS 10.30.23.1
/etc/udhcpc.d/50default: Adding DNS 5.249.128.38
done.
Starting rpcbind daemon...done.
Fuse filesystem already available.
Mounting fuse control filesystem.
exportfs: can't open /etc/exports for reading
starting 8 nfsd kernel threads: done
starting mountd: rpc.mountd: svc_tli_create: could not open connection for udp6
rpc.mountd: svc_tli_create: could not open connection for tcp6
rpc.mountd: svc_tli_create: could not open connection for udp6
rpc.mountd: svc_tli_create: could not open connection for tcp6
rpc.mountd: svc_tli_create: could not open connection for udp6
rpc.mountd: svc_tli_create: could not open connection for tcp6
done
Mounting remote filesystems...
Starting automount: /sbin/stb-hwclock: line 24: /proc/stb/fp/rtc: No such file or directory
done.
starting statd: done
Starting internet superserver: inetd.
Starting Samba: smbd wsdd.
Starting Shell In A Box server: shellinabox.
Starting syslogd/klogd: done
Starting telnet server: telnetd.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
Process 1862 died: No such process; trying to remove PID file. (/run/avahi-daemon//pid)
...done.
* starting FTP Server: vsftpd... done.
Starting crond: OK
/etc/rc3.d/S98createswap: line 4: fdisk: command not found
[ 15.446035] blk_update_request: I/O error, dev mmcblk0rpmb, sector 0
[ 15.472024] blk_update_request: I/O error, dev mmcblk0rpmb, sector 0
Warning: Error fsyncing/closing /dev/mmcblk0rpmb: Input/o[ 15.482646] blk_update_request: I/O error, dev mmcblk0rpmb, sector 0
utput error
Warning: Error fsyncing/closing /dev/mmcblk0rpmb: Input/output error
Error: The backup GPT table is corrupt, but the primary appears OK, so that will be used.
Warning: Not all of the space available to /dev/mmcblk0 appears to be used, you can fix the GPT to use all of the space (an extra 40960 blocks) or continue with the current setting?
Running local boot scripts (/etc/rc.local).
killall: showiframe: no process killed
/dev/dvb/adapter0/video0: No such file or directory
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
net.ipv4.tcp_timestamps = 0
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 11
/usr/bin/enigma2.sh: line 149: 1904 Segmentation fault LD_PRELOAD=$LIBS /usr/bin/enigma2 $VERBOSE 2> /dev/null
killall: showiframe: no process killed
/dev/dvb/adapter0/video0: No such file or directory
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
net.ipv4.tcp_timestamps = 0
PYTHONPATH: /usr/lib/enigma2/python