Tocmai ca procedura de mai sus nu a mers, banuiesc ca-i bushit bootloaderul!
Tocmai ca procedura de mai sus nu a mers, banuiesc ca-i bushit bootloaderul!
cred ca e vorba despre o procedura prin serial, telesat spune:
Potrebno je imati :
TFTPD32
backup_kernel
putty
Seriski Interface za povezivanje sa AZBoxom
Potrebno je znati koja je IP adresa vaseg racunara, to mozete saznati ako udjete u command promt,
znaci idete na Start pa u polje run upisete cmd i pritisnete enter, onda kucajte ipconfig i enter i dobicete info o IP adresi
Predpostavimo da je IP adresa na vasem racunaru : 192.168.1.12 (potrebno u nastavku teksta)
U tom slucaju biramo IP adresu za AZBox u rangu gde je IP od racunara , uzecemo recimo : 192.168.1.34
1.Pokrenite TFTPD32
2.Pokrenite Putty , prebacite na serial, upisite COM-port na kome je vezan vas seriski interfejs , pod Speed upisite 115200
3.Povezite seriski interface sa AZBoxom i ukljucite AZBox
4.Pratisnite CTRL+C da bi prekinuli bootiranje
5.kucajte :
setxenv y.ipaddr "192.168.1.34"
setxenv y.gateway "192.168.1.1"
setxenv y.subnetmask "255.255.255.0"
net init
load -b tftp://192.168.1.12/backup_kernel 0xb0100000
pflash write -f 0x80000 0xb0100000 0x680000
Sada cekate da prvo obrise deo FLASH-a , pa onda da upise novi sadrzaj.
Ovo traje oko 5-6minuta , budite strpljivi da zavrsi i na kraju rebootajte vas AZBox.
Ako je sve proslo kako treba, dobicete na TV-u standardni update koji vam je poznat,
ubacite USB stick sa Oficijalnim FW-om i ubacitega kao i do sada.
http://rapidshare.com/files/40839862...erial.rar.html
Am sa-mi fac timp pentru pregatirea serialului si am sa aduc vesti dupa!
E2_1.0.21_elite_premium
http://www.megaupload.com/?d=W8PZZJ5A
http://rapidshare.com/files/406526152/patch.rar.html
//EDIT:
1. Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, (patch version: 1.0.21 E2 by TheRipper, press OK, wait to finish, reboot - don't remove stick !)
4. Start AZUp , write IP adress of AZBox (see VFD), then click on Update button on AZUp, wait and follow message on AZUp and VFD, when all done - wait for reboot msg on VFD and then remove USB stick
RSP-TEAM
am incercat sa pun E2_1.0.21_elite_premium pe azbox premium si a murit nu mai faci nimic am respectat toti pasi de instalare
acum apare pe display: geek :P si rescue mode? ce sa fac sa pun pe picoare azboxul?
Last edited by romix; 21-09-10 at 12:45.
incearca asta:
by @hfmlsok, i am trying to go back to azbox firmware , i put original patch.bin in usb fat32, reboot, i get rescue mode and ip,and it says everytime at 80% unsupported firmware version! in AZup
damn, what should i do now?
edit: DON'T USE KGD FIRMWARE TO RECOVER. USE ORIGINAL OPENSAT'S FIRMWARE FIRST.OTHERWISE IT WON'T WORK IN AZUP
edit2: after reboot azbox and close and open again AZup i managed to flash azbox back to original
incearca pe portul USB din spate, eventual un fw original OpenSAT(0.9.3877)
p.s. dar ai lansat AZup pentru finalizare?
---------- Post added at 13:06 ---------- Previous post was at 12:50 ----------
If You want to load this version of Enigma 2 for AzBox HD Elite / Premium please follow this procedure :
1 . Load this patch.bin ( Enigma 2 ) file on FAT32 formatted USB Memory Stick
2. Turn Off Your AzBox HD Device, put USB Memory Stick inside and Turn on AzBox HD Device.
3. Follow the procedure USB Update on the screen, after process is finished, remove the USB stick from the AzBox HD Device, and let AzBox HD to Reboot
4. After reboot is finished, You should be in Enigma 2 AzBox HD Running state
5. If You tested enough Enigma 2 on AzBox HD Device and want to be back on AzBox Official Firmware, it is piece of cake
6. Load on FAT32 Formatted USB Memory stick patch.bin ( Official AzBox HD Firmware e.g 0.9.5020 ) .
7. Turn Off AzBox HD Device, put USB Memory stick in Receiver, and Turn it on.
8. On VFD You will see RESCUE MODE and IP Address will be listed.
9. On Your PC run application called AzUP by our team member telesat, enter IP of Your AzBox HD Device and click on UPDATE
10. Wait that Update is finished, and You will have again AzBox HD Official Firmware
This is totally RISK FREE Installation and Recovery procedure for AzBox HD Elite / Premium Devices !!!
Last edited by qwess; 21-09-10 at 13:02. Reason: completare
Azbox HD with OpenSPA 3.0 powered by OSCam
UE46F8000 powered by SamyGO_OSCam
am lansat azup si nu se conecteaza la azbox am incercat sa pun Firmware - rev. 0.9.3877 si nimic acelasi mesaji RESCUE MODE?