Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 15 of 20

Thread: "Resuscitarea" - rescrierea flash-ului la Kathy

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #15
    Member Beginner
    Join Date
    22 Dec 2008
    Posts
    13
    Mentioned
    0 Post(s)
    Rep Power
    0

    Default

    asta-i ce obtin
    am incercat cu 3 stickuri

    de acolo cred ca-i problema dar nu stiu ce inseamna
    """"""hm, page 002c9000 reserved twice"""""

    sa incerc metoda lui groschien de mai sus?



    Board: STb7100-mboard

    U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
    DRAM: 32 MB
    write time out = 1, clock = 40
    write time out = 1, clock = 40
    Flash: 16 MB
    *** Warning - bad CRC, using default environment
    In: serial
    Out: serial
    Err: serial
    pll0 freq 531
    pll1 freq 399
    Net: VFD_Driver Init
    VFD_Controller Type : NEW Kathrein VFD
    board_version = 0
    Button_value = 7
    STB7100-REF> loadb a4000000
    ## Ready for binary (kermit) download to 0xA4000000 at 115200 bps...
    ## Total Size = 0x0025fd56 = 2489686 Bytes
    ## Start Addr = 0xA4000000
    STB7100-REF> bootm a4000000
    ## Booting image at a4000000 ...
    Image Name: Emergency system (captaintrip)
    Image Type: SH-4 Linux Kernel Image (gzip compressed)
    Data Size: 2489622 Bytes = 2.4 MB
    Load Address: 84401000
    Entry Point: 84402000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
    Starting kernel @à@ - 0x00000000 - 0 ...
    Linux version 2.6.11.12_stm20-33 (root@localhost.localdomain) (gcc-Version 3.4.3 (STMicroelectronics/Linux Base 3.4.3-19) [build Mar 10 2006]) #6 Mon Jul 2 01:01:25 CEST 2007
    hm, page 002c9000 reserved twice.
    ....
    ....
    ....etc
    hm, page 003b6000 reserved twice.
    STMicroelectronics STb7100 Marusys MSS-5000 Custom board initialisation
    STb7100 version 3.x
    Built 1 zonelists
    Kernel command line: console=ttyAS0,115200 root=/dev/ram0 ramdisk_size=2688 mem=32m bigphysarea=4000 coprocessor_mem=2m@0x04000000,2m@0x04200000
    st-coprocessor: Failed to reserve memory at 0x04000000
    st-coprocessor: Failed to reserve memory at 0x04200000
    PID hash table entries: 256 (order: 8, 4096 bytes)
    Calculated peripheral clock value 66938928 differs from sh_pclk value 66000000, fixing..
    PLL1 : 531.00MHz
    PLL2 : 399.00MHz
    ST40 CPU : 265.50MHz
    ST40 BUS : 132.75MHz
    ST40 PER : 66.37MHz
    SLIM : 265.50MHz
    ST231 : 399.00MHz
    STBUS : 199.50MHz
    EMI : 99.75MHz
    LMI : 199.50MHz
    FSYN0_CHAN1 : 108.008MHz
    FSYN0_CHAN2 : 36.866MHz
    FSYN0_CHAN3 : 32.768MHz
    FSYN1_CHAN1 : 27.002MHz
    FSYN1_CHAN2 : 150.008MHz
    FSYN1_CHAN3 : 27.002MHz
    FSYN1_CHAN4 : 48.000MHz
    CLK_PIX_HD : 108.008MHz
    CLK_PIX_SD : 27.002MHz
    CLK_DISP_HD : 13.501MHz
    CLK_DISP_ID : 13.501MHz
    CLK_GDP2 : 27.002MHz
    CLK_656 : 27.002MHz
    CLK_PIPE : 150.008MHz
    CLK_PP : 27.002MHz
    CLK_IC_150 : 150.008MHz
    CLK_DAA : 32.768MHz
    CLK_DSS : 36.866MHz
    CLK_LPC : 46.875KHz
    CLK_BCH_HDMI : 108.008MHz
    CLK_TMDS_HDMI: 27.002MHz
    CLK_PIX_HDMI : 13.501MHz
    CLK_DVP : VIDINCLK
    CLK_RTC : 27.002MHz
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Memory: 12344k/32768k available (2586k kernel code, 20380k reserved, 1218k data, 96k init)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: STb710x
    checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
    Freeing initrd memory: 952k freed
    NET: Registered protocol family 16
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    SH Virtual Bus initialized
    bigphysarea: Allocated 4000 pages at 0x84839000.
    JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
    Initializing Cryptographic API
    Device probe found data for platform device lirc
    lirc_dev: IR Remote Control driver registered, at major 61
    lirc_dev: lirc_register_plugin: sample_rate: 0
    STM LIRC plugin has IRQ 125
    Lirc STM: Using IRB mode
    STMicroelectronics LIRC driver configured
    STPIO layer initialised
    Device probe found data for platform device wdt
    STM watchdog initialized
    STMicroelectronics ASC driver initialized
    asc_init: check the clock
    ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
    asc_init: check the clock
    ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered
    RAMDISK driver initialized: 16 RAM disks of 2688K size 1024 blocksize
    loop: loaded (max 8 devices)
    Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
    Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
    Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
    Amd/Fujitsu Extended Query Table at 0x0040
    Onboard_Flash: CFI does not contain boot bank location. Assuming top.
    number of CFI chips: 2
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    Creating 8 MTD partitions on "Onboard_Flash":
    0x00000000-0x00020000 : "Boot firmware : 0xA000.0000-0xA001.FFFF"
    0x00040000-0x00200000 : "Kernel - 0xA004.0000-0xA01F.FFFF"
    0x00200000-0x002a0000 : "Config FS - 0xA020.0000-0xA029.FFFF"
    0x002a0000-0x004e0000 : "Root FS- 0xA02A.0000-0xA04D.FFFF"
    0x004e0000-0x00ae0000 : "APP_Modules 0xA04E.0000-0xA0AD.FFFF"
    0x00ae0000-0x00c00000 : "EmergencyRoot 0xA0AE.0000-0xA0BF.FFFF"
    0x00c00000-0x01000000 : "OtherData 0xA0C0.0000-0xA0FF.FFFF"
    0x00020000-0x00040000 : "BootConfiguration 0xA002.0000-0xA003.FFFF"
    ST40_start_host_control
    ST40_start_host_control proceeding
    drivers/usb/host/ehci-stcore.c: ehci_hcd (ST40) at 0xb91ffe00,irq 169
    ST40-ehci ST40-ehci2: new USB bus registered, assigned bus number 1
    ST40-ehci ST40-ehci2: park 0
    ST40-ehci ST40-ehci2: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    out
    Initializing USB Mass Storage driver...
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    i2c /dev entries driver
    stssc layer initialized
    STMicroelectronics - Coprocessors st231 Init
    st231-0 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xa4000000 size 0x00200000
    cop. addr 0x04000000
    Channels : Not defined
    IRQ : not used
    ---------------------------------------------------------------
    st231-1 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xa4200000 size 0x00200000
    cop. addr 0x04200000
    Channels : Not defined
    IRQ : not used
    ---------------------------------------------------------------
    NET: Registered protocol family 2
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    NET: Registered protocol family 1
    RAMDISK: Compressed image found at block 0
    usb 1-1: new high speed USB device using ST40-ehci and address 2
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    usb 1-1.4: new high speed USB device using ST40-ehci and address 3
    VFS: Mounted root (ext2 filesystem) readonly.
    Freeing unused kernel memory: 96k freed
    scsi0 : SCSI emulation for USB Mass Storage devices
    /etc/init.d/rcS running...
    Remounting root file system in read-write mode...mount: Mounting 211.235.241.247:/ on / failed: Invalid argument
    [FAILED]
    /etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Read-only file system
    Mounting other file systems...Eep. No valid nodes for ino #1
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000: 0x1354 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000004: 0xe9ce instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000008: 0x57ef instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000000c: 0xc80c instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0xd2f3 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000014: 0x9c91 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000018: 0x4bab instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000001c: 0x43e3 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000020: 0xc097 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000024: 0x30be instead
    Further such events for this erase block will not be printed
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010000: 0x45fd instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010004: 0xfb07 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010008: 0x0024 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001000c: 0x8445 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010010: 0xdede instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010014: 0xf223 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010018: 0x9e19 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001001c: 0x9337 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010020: 0xd426 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010024: 0x8317 instead
    Further such events for this erase block will not be printed
    Old JFFS2 bitmask found at 0x000147d4
    You cannot use older JFFS2 filesystems with newer kernels
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020000: 0x4fe9 instead
    jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020004: 0x9de5 instead


    samd samd
    Last edited by mr_dexter; 17-11-09 at 21:32.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •