Tivusat, ma ajuta cineva?

**popamare** · 17-06-16, 20:06

Card Tivusat 183d, pus in doua receptoare (Vu+ Solo2, intern sau smargo sau DM500+ intern), incercate cateva versiuni de oscam, aceeasi problema

Code:

1970/01/01 02:32:22 10121720 r bla [internal] Reader initialized (device=/dev/sci0, detect=cd, pll max=27.00 MHz, wanted mhz=3.68 MHz1970/01/01 02:32:23 10121720 r bla [internal] card detected
1970/01/01 02:32:24 10121720 r bla [internal] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64 
1970/01/01 02:32:24 10121720 r bla [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
1970/01/01 02:32:24 10121720 r bla [internal]  TEST tempo mhz check = 500 mhz
1970/01/01 02:32:24 10121720 r bla [internal] Calculated work ETU is 5.93 us reader mhz = 540
1970/01/01 02:32:24 10121720 r bla [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 5.40 Mhz (nearest possible mhz specified reader->cardmhz)
1970/01/01 02:32:25 10121720 r bla [internal] detect nagra tiger card
1970/01/01 02:32:25 10121720 r bla [internal] card system not supported
1970/01/01 02:32:25 10121720 r bla [internal] Normal mode failed, reverting to Deprecated Mode
1970/01/01 02:32:26 10121720 r bla [internal] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64 
1970/01/01 02:32:26 10121720 r bla [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
1970/01/01 02:32:26 10121720 r bla [internal]  TEST tempo mhz check = 500 mhz
1970/01/01 02:32:26 10121720 r bla [internal] Calculated work ETU is 82.67 us reader mhz = 450
1970/01/01 02:32:26 10121720 r bla [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 4.50 Mhz (nearest possible mhz specified reader->cardmhz)
1970/01/01 02:32:27 10121720 r bla [internal] detect nagra tiger card
1970/01/01 02:32:28 10121720 r bla [internal] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
1970/01/01 02:32:30 10121720 r bla [internal] T1 Resync command error, trying to reactivate!
1970/01/01 02:32:30 10121720 r bla [internal] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64 
1970/01/01 02:32:30 10121720 r bla [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
1970/01/01 02:32:30 10121720 r bla [internal]  TEST tempo mhz check = 500 mhz
1970/01/01 02:32:30 10121720 r bla [internal] Calculated work ETU is 5.93 us reader mhz = 540
1970/01/01 02:32:30 10121720 r bla [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 5.40 Mhz (nearest possible mhz specified reader->cardmhz)
1970/01/01 02:32:30 10121720 r bla [internal] card system not supported
1970/01/01 02:32:30 10121720 r bla [internal] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
1970/01/01 02:32:30 10121720 r bla [internal] card initializing error
1970/01/01 02:32:31        0 s init for all local cards done

Am incercat diferite setari in [reade], eroarea actuala data cu acestea

Code:

[reader]enabled = 1
label = bla
protocol = internal
device = /dev/sci0
caid = 183D
rsakey = A92............B5
ecmwhitelist = 91
ecmheaderwhitelist = 80308ED387,81308ED387
detect = cd
nagra_read = 2
mhz = 368
cardmhz = 2700
ident = 183D:000000,005411
group = 2
emmcache = 1,1,1
blockemm-unknown = 1
blockemm-g = 0
blockemm-u = 0

Vreo idee ??? Ca eu sunt depasit...

Cardul face lumina in camul lui sau in cccam (la acesta fara nici un fel de setare speciala). Intr-unul din cititoarele interne ale vu plusului mai am un HD+ 1843 care merge fara probleme....

Ms

**mirel** · 17-06-16, 21:47

salut...
incearca in vu+ cu:

PHP Code:


detect = cd
mhz = 450
cardmhz = 2700

**popamare** · 17-06-16, 22:46

Aceeasi problema.

**mirel** · 17-06-16, 22:48

autospeed enable?

**danysev** · 18-06-16, 14:07

incearca un upgrade la oscam

[reader]
label = TivuSat
protocol = internal
device = /dev/sci0
services = tivusat
lb_whitelist_services = tivusat
autospeed = 0
caid = 183D,183E
rsakey = A9...B5
detect = cd
nagra_read = 1
mhz = 450
cardmhz = 2700
ident = 183E:005411,000000;183D:005411,000000
group = 1
emmcache = 2,1,2,1
blockemm-unknown = 1
auprovid = 005411

daca nu o ia, ai nevoie de un easymouse2

**popamare** · 18-06-16, 21:35

Tot nu merge...

Va rog sa-mi dati un rsa in pm poate e asta gresit, nu stiu. Cred totusi ca emulatorul e de vina , pentru ca in cccam 230 merge fara probleme cu ecm sub 0,200 in readerul de la Vu+.

Am 2 Smargo Crystal si doua Smartreadere (Argolis parca) toate de la satmultimedia, nici in ele nu merge minunea asta de card (in oscam). Din ce-mi amintesc nici HD+ din dotare nu mergea in ele (tot nagra), nu mai stiu ce eroare dadea. In schimb au mers mai multe carduri (cworks de ex), ia acum am in ele freesat via si conax si focus care n-au nici o problema.
Deci daca nu merge in astea care ar fi riscul sa mai iau un cititor de card si sa nu mearga? Nu-mi dau seama daca easymouse2 e ceva diferit sau nu (nu am avut mult timp sa studiez chestiunea... noob)

Asa arata Crystal
http://www.tvsatnitra.sk/obchod/acti...-crystal.xhtml

Are pe el 4 comutatoare
1: comuta intre 3,3v si 5v
2: comuta intre SmartMouse si Phoenix
3: comuta intre o sageata (indreptata catre 4) si 3,579mhz
4: comuta frecventele : 5mhz, 8mhz, 10mhz si Y5
Astea nu mi-au mers decat in combinatia : 5v / phoenix / 3,579mhz (cu cardurile care imi merg desigur, de ex cardul freesat viacces, sau tntsat la vremea lui, etc). Nu stiu sa setez asa ceva. :/

Poate imi ziceti ce sa setez hard sau/si soft (oscam) acest Smargo Crystal... poate... poate....

Multumesc... simt ca mi-a ramas doar sa ma rog....

**danysev** · 18-06-16, 22:28

In pagina de. Oscam ai debug bifează de la 1la 32 și tine pornit doar reader-ul de tivusat

Trimis de pe al meu Nexus 5 folosind Tapatalk

---------- Post added at 21:28 ---------- Previous post was at 21:28 ----------

**danysev** · 18-06-16, 22:34

am compilat oscam cu de toate https://mega.nz/#!f9cRlI5Y!X_6zgDRDvvKan-RECRL85NJ78N9KVGe0iacLd5cCVdM

**popamare** · 19-06-16, 00:15

hmmmmm

[CODE]

2016/06/18 22:54:00 00000000 s (main) waiting for local card init
2016/06/18 22:54:01 5270C3B1 r (reader) TivuSat [internal] card detected
2016/06/18 22:54:02 5270C3B1 r (reader) TivuSat [internal] ATR: 3F FF 95 00 FF 91 81 71 FF 47 00 54 49 47 45 52 30 30 33 20 52 65 76 32 35 30 64
2016/06/18 22:54:02 5270C3B1 r (reader) TivuSat [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
2016/06/18 22:54:02 5270C3B1 r (reader) TivuSat [internal] Calculated work ETU is 7.11 us reader mhz = 450
2016/06/18 22:54:05 5270C3B1 r (reader) TivuSat [internal] Buffers readed 0 bytes total time_us 3099274
2016/06/18 22:54:06 5270C3B1 r (reader) TivuSat [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 4.50 Mhz (nearest possible mhz specified reader->mhz)
2016/06/18 22:54:07 5270C3B1 r (reader) TivuSat [internal] detect nagra tiger card
2016/06/18 22:54:07 5270C3B1 r (reader) TivuSat [internal] type: NAGRA, caid: 183D, IRD ID: ############
2016/06/18 22:54:07 5270C3B1 r (reader) TivuSat [internal] ProviderID: 00 00 54 11
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [internal] ready for requests
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [internal] found card system nagra
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] THIS WAS A SUCCESSFUL START ATTEMPT No 1 out of max alloted of 1
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] ROM: T I G E R 0 0 3
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] REV: R e v 2 5 0
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] SER: ############
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] CAID: 183D
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] Prv.ID: 00 00 54 11 (sysid)
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] Activation Date : 01/01/2009
2016/06/18 22:54:08 5270C3B1 r (reader) TivuSat [nagra] Expiry Date : 01/01/2038
2016/06/18 22:54:08 00000000 s (main) init for all local cards done
2016/06/18 22:54:08 00000000 s (emmcache) loading emmcache disabled since no reader is using it!
2016/06/18 22:54:08 00000000 s (emmcache) loading emmstats disabled since no reader is using it!
2016/06/18 22:54:08 00000000 s (anticasc) anti cascading disabled

[CODE/]

---------- Post added at 22:58 ---------- Previous post was at 22:56 ----------

SI........................

[CODE]

2016/06/18 22:59:01 1D3B755F c (ecm) bibisor (183D/B7): not found (2 ms) by TivuSat
2016/06/18 22:59:01 05FE196A c (ecm) Polliia (183D/91): cache1 (1 ms) by TivuSat - Rai 1 HD
2016/06/18 22:59:01 791108C0 c (ecm) petiofi (183D/91): found (193 ms) by TivuSat - Rai 1
2016/06/18 22:59:03 05FE196A c (ecm) Polliia (183D/91): cache1 (1 ms) by TivuSat - Rai 1
2016/06/18 22:59:09 791108C0 c (ecm) petiofi (183D/91): cache2 (125 ms) by TivuSat - Rai 1 HD
2016/06/18 22:59:09 38BAD023 c (ecm) anonymous (183D/91): found (193 ms) by TivuSat - Rai 1 HD
2016/06/18 22:59:10 05FE196A c (ecm) Polliia (183D/91): found (192 ms) by TivuSat
2016/06/18 22:59:11 05FE196A c (-) -- Skipped 1 duplicated log lines --
2016/06/18 22:59:11 05FE196A c (ecm) Polliia (183D/91): cache1 (1 ms) by TivuSat - Rai 1 HD
2016/06/18 22:59:11

[CODE/]

---------- Post added at 23:02 ---------- Previous post was at 22:58 ----------

Merge !!!!!!!!

Deci era de la emulator....

Sa vad cum merge si cu restul cardurilor.

Danny, la ce te referi cand spui "cu de toate" ?

Multe multumiri

---------- Post added at 23:15 ---------- Previous post was at 23:02 ----------

Danny, te rog zi-mi setarile corecte pentru fiecare card

[CODE]
[reader]
label = TivuSat
protocol = internal
device = /dev/sci1
services = tivusat
lb_whitelist_services = tivusat
autospeed = 0
caid = 183D,183E
rsakey = A9....B5
detect = cd
nagra_read = 1
mhz = 450
cardmhz = 2700
ident = 183E:005411,000000;183D:005411,000000
group = 1
emmcache = 2,1,2,1
blockemm-unknown = 1
auprovid = 005411

[reader]
label = Focus
description = Focus
protocol = smargo
device = /dev/ttyUSB0
smargopatch = 1
caid = 0B02
detect = cd
mhz = 534
cardmhz = 600
ident = 0B02:000000
group = 1
audisabled = 1

[reader]
label = Freesat
description = Freesat
protocol = smargo
device = /dev/ttyUSB1
smargopatch = 1
autospeed = 0
caid = 0B02
detect = cd
mhz = 600
cardmhz = 600
ident = 0B02:000000
group = 1
audisabled = 1

[reader]
label = HD+
protocol = internal
device = /dev/sci0
caid = 1843
boxkey = A7.........7C
rsakey = BF......D5
detect = cd
mhz = 450
cardmhz = 2700
group = 1
dropbadcws = 1
audisabled = 1

[reader]
label = TvrHD
description = TvrHD
protocol = mouse
device = /dev/ttyUSB2
smargopatch = 1
detect = cd
group = 1
audisabled = 1

[CODE/]

**danysev** · 19-06-16, 00:40

Cardmhz=357 la toate readerele externe in rest e bine. MHz definește frecventa setata pe fiecare reader. La cele neagra ar trebui cardmhz=368(pe readere externe). In

Trimis de pe al meu Nexus 5 folosind Tapatalk

**MihaiP** · 19-06-16, 13:17

tiger_rsakey =

Code:

A92DA72FEEACF2947B003ED652153B189E4043B0138C368BDF6B9ED77DDAD6C0761A2198AEB3FC97A19C9D01CA769B3FFFE4F6E70FA4E0696A8980E18D8C58E11D817121346E3E66457FDD84CFA72589B25B538EFC304361B54845F39E9EFA52D805E5FD86B595B366C35716ABC91FA3DC159C9F4D8164B5

tiger_ideakey = 37373737373737373737373737373737

[CODE]
[reader]
label = TivuSat
protocol = internal
device = /dev/sci1
services = tivusat
lb_whitelist_services = tivusat
autospeed = 0
caid = 183D,183E
rsakey = A9....B5
detect = cd
nagra_read = 1
mhz = 450
cardmhz = 2700
ident = 183E:005411,000000;183D:005411,000000
group = 1
emmcache = 2,1,2,1
blockemm-unknown = 1
auprovid = 005411

**coco** · 18-11-23, 10:42

Buna ziua, am o rugaminte la cei care stiu, as vrea sa-mi cumpar o cartela Tivusat si cam, ce sfat imi dati?
Activarea ei in Romania cum se face?
P.S.as vrea sa o folosesc in oscam.
ms

**fery21** · 18-11-23, 10:51

Salut, in comerț găsești doar carduri verzi sau negre(1856 caid) care nu merg in CS doar in cam tivusat, cat despre cardurile vechi e riscat de oare ce nu sti daca va-fi dezactivat(183D -tig02-tig-03) care sunt doar hd, cardul galben (tot hd nu deschide 4K) rar de gasit cu caid 183D sunt imortale, cardurile gri (183E) nu mai fac au doar in cam original tivusat, dar sunt anumite script-uri care trimit emm corect la acest card daca este in oscam.

**paulino** · 03-12-23, 16:50

Si eu am un card !83E pe care nu reusesc sa il pornesc.
@danysev vezi ca linkul https://mega.nz/#!f9cRlI5Y!X_6zgDRDv...Ge0iacLd5cCVdM nu mai este valabil.Poate mai pui odata!

**fery21** · 04-12-23, 00:05

Este aici la zi

Thread: Tivusat, ma ajuta cineva?

Thread Tools

Display

Hybrid View

Tivusat, ma ajuta cineva?

Posting Permissions