Amiko Alien 1 blocat la LOAD

[tempuser]

Asta imi apare din Putty:

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1f f8
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force rs232 upgrade u-boot, need 524288 Bytes(512kB)
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCCTimed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes

Transmit filesize is 0, please check your choiced file



Daca il pornesc normal asta imi apara in Putty

Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD


U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel

DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1f f8
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCCTimed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes

[zildan]

Vezi ce faci cu 3 !!!!
Asa il strici!

---------- Post added at 19:36 ---------- Previous post was at 19:36 ----------

Opreste boot-ul si da comanda "printenv" .

[tempuser]

cum opresc boot-ul? daca apas esc imi apare un meniu cu optiuni update uboot update kernel update rootfs exit boot reset loader

[zildan]

Hit ESC to stop autoboot:

[tempuser]

MB618> "printenv"
bootdelay=3
baudrate=115200
board=mb618
monitor_base=0xA0000000
monitor_len=0x00080000
monitor_sec=0xa0000000 0xa007ffff
load_addr=0x80000000
unprot=protect off $monitor_sec
update=protect off $monitor_sec;erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec
HOSTNAME=LINUX7109
ethaddr=00:80:E1:12:06:38
ipaddr=192.168.40.63
netmask=255.255.255.0
gatewayip=192.168.3.1
serverip=192.168.40.19
kernel_base_spark= 0xa0080000
kernel_base_enigma2=0x18000000
kernel_sec= a0080000 a077ffff
kernel_len= 0x00700000
update_kernel=protect off a0080000 a077ffff ;erase a0080000 a077ffff ;cp.b 0x80000000 0xa0080000 0x00700000 ;protect on a0080000 a077ffff
rootfs_base=0xa0800000
rootfs_sec=a0800000 a1ffffff
menucmd=update
tftp_kernel_name_spark=mImage
tftp_kernel_name_enigma2=uImage
tftp_userfs_name_spark=userfsub.img
tftp_userfs_name_enigma2=e2jffs2.img
kernel_name_spark=spark/mImage
kernel_name_enigma2=enigma2/uImage
userfs_name_spark=spark/userfsub.img
userfs_name_enigma2=enigma2/e2jffs2.img
userfs_base_spark=800000
userfs_base_enigma2=18800000
userfs_len_spark=17800000
userfs_len_enigma2=7700000
kernelnfspath=192.168.40.19:/opt/target
rootfs_name=UserFS
rootfsnfspath=192.168.40.19:/home/d22cj/workspace/target
uboot_name=u-boot.bin
ubootnfspath=192.168.40.19:/home/d22cj/workspace/target
bootfromnfs=nfs a4000000 $kernelnfspath/$kernel_name;bootm a4000000
bootargs_nfs=console=ttyAS0,115200 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 stmmaceth=msglvl:0,phyaddr:1:watchdog:5000 root=/dev/nfs nfsroot=192.168.40.19:/opt/target,nfsvers=2,rsize=4096,wsize=8192,tcp rw ip=192.168.40.61:192.168.40.19:192.168.3.1:255.255.0.0:LINUX7109:eth0ff bigphysarea=4000
bootargs_flash=console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000
bootargs_spark=console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000
bootargs_enigma2=console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:61 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0ff bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:2,watchdog:5000
magic_version=1.7
filesize=4000000
fuseburned=true
bootargs=console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:80:E1:12:40:69 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000
kernel_base= 0xa0080000
kernel_name=spark/mImage
userfs_name=spark/userfsub.img
tftp_kernel_name=mImage
tftp_userfs_name=userfsub.img
userfs_len=17800000
userfs_base=800000
boot_system=spark
bootcmd=bootm 0xa0080000
stdin=serial
stdout=serial
stderr=serial

Environment size: 3127/131068 bytes


Asta nu cred ca e normal:

MB618> mtest
Testing 80000000 ... 87d00000 (125 MiB):
Pattern 00000000 Writing... Reading...
Mem error @ 0x876DFA5C: found 87F0BC90, expected 01DB7E97

Mem error @ 0x876DFA60: found 876DFA60, expected 01DB7E98

Mem error @ 0x876DFA64: found 876DFA60, expected 01DB7E99

Mem error @ 0x876DFA68: found 876DFA60, expected 01DB7E9A

Mem error @ 0x876DFA6C: found 01DB7E9A, expected 01DB7E9B
Pattern FFFFFFFF Writing...

[tempuser]

Se poate formata memoria, asemenea unui stick usb? Sau o pot inlocui, la fel cum inlocuiesti o memorie ram de pc?
Se mai poate face ceva?

[tempuser]

Exista 2 versiuni de enigma 2 (Flash si USB), cum pot sa instalez enigma2 pe USB si sa bootez de pe stick, nu sa o incarce in Flash?