Gbox+Mgcamd

[Einstein]

La mine am asa mg_cfg:

M: { 01 }
C: { 02 }
A: { 02 }
U: { 05 }
T: { 00 }
G: { 08 }
N: { 07 } 5 30
K: { 05 }
Q: { 600 }
P: { 00 }
O: { 00 } user parola ===> aici cum ai la dream user si pass
S: { 03 } 80
L: { 03 } 192.168.1.02 28007 /tmp/mgcamd.log ===> IP-ul tau de la dream
E: { 15 }
H: { 07 }
R: { 04 }
D: { 00 }
B: { 02 }

Merge perfect cu aceasta configuratie la mine!

[mondo]

Da.Sunt bune setarile din mg_cfg.Dar el vrea linia O din gbox_cfg.
Sau cel putin asa am inteles eu!!!

[Einstein]

Acolo am asa:

O: { 03 } 192.168.1.02 ===> IP-ul dream
celelalte:

W: { 00 00 } 9600
G: { 03 }
C: { 01 }
M: { 00}
A: { 01 }
U: { 01 }
H: { 01 }
T: { 00 }
L: { 00 } 192.168.1.02 8029
Z: { 00 12 } 192.168.1.01 8024
V: { F0 35 }

[mondo]

La mine cu O: { 03 } ip dream, este enervant.Imi arata mereu pe ecranul TV un mesaj.Sa stau mereu sa anulez mesajul....e...ce sa mai....nu ma satisface!!!
O: { 00 } cel mai bine!

[fery21]

/ / mbox.cfg explicaţie şi exemple



B: (0)

/ / B: (x)
/ / x = 0 -> dezactivează locale porturile UDP 8004-80xx, acest porturi sunt folosite cu placii si gbox dop (Windows şi Linux)
/ / x = 1 -> activează
/ / implicit de a dezactiva


Z: (12)) (127.0.0.1 8000

/ / Z opţiunea -> trimiterea de control / scris actuale informatii
/ / Z: XY) ((IP port)
/ / X = 0 -> nu de imprimare timp de timbru (in consola de depanare cu ecran şi in fişier)
/ / X = 1 -> de imprimare timp de timbru (....)
/ / Y = 0 -> nu scris / trimiterea de informatii pentru a depana fişierul / IP de destinaţie
/ / Y = 1 -> trimite informatii la destinaţie de IP, dar nu in fişierul de depanare
/ / Y = 2 -> informatii pentru a scrie fişierul de depanare, dar nu trimite la destinaţie IP
/ / Y = 3 -> scrie / trimite informaţii de depanare pentru a fişierului / IP de destinaţie
/ / Portul de IP -> destinaţie de IP şi portul UDP in cazul in care pentru a trimite informatii
/ / Nu implicit



C #: 127.0.0.1 7999) (

/ / C opţiunea -> control la primirea unor mesaje de comandă local sau de pe un alt IP
/ / C: (IP port)
/ / IP-> dvs. de IP local sau vă DNS
/ / Port -> pe ce port va fi aşteaptă comandă de mesaje
/ / Nu implicit


U: (1)

/ / U Options -> Update peer (e) in cazul in care IP-peer de modificări in timp ce incă resending ECM's / CW etc. informaţii
/ / Implicit numai pe hello peer mesaj (e) de IP sunt actualizate!!!
/ / U: (x)
/ / X = 0 -> dezactivat
/ / X = 1 -> activată
/ / Implicit dezactivat



L: (1)

/ / L opţiunea -> cum să mbox virtual de carte de menage (e) cu nivel 0
/ / (Numai pentru peer (e) care au si poate reshare cardurile virtuale, dar nu doriţi să utilizaţi cartea de nivel 0 (e) pentru a le auto)
/ / L: (x)
/ / X = 0 -> nu incarca nici cu cardurile virtuale de nivel 0, nu aveţi posibilitatea să le folosească pentru auto
/ / X = 1 -> incarca cu toate cardurile virtuale de nivel 0, pe care il veţi folosi pentru a le dvs. auto
/ / Implicit 1


T: (0)

/ / T opţiunea -> unde să stocaţi fişierele de temp ... (share.info, debug.txt, etc)
/ / T: (folder_path_to_files, de exemplu: T: (/ tmp /))
/ / Default 0 ===> calea folderului in cazul in care fişierul este mbox.xxx!!!!


K: (0)

/ / K opţiunea -> unde este cwshare.cfg fişier
/ / K: (folder_path_to_files, de exemplu: K: (/ var / keys /))
/ / Default 0 ===> calea folderului in cazul in care fişierul este mbox.xxx!!!!


E: (1)

/ / E opţiunea -> dezactivează acelaşi cartele de la colegii de breaslă
/ / E: (x)
/ / X = 0 -> cardurile de utilizare acelaşi (boxids) de la colegii de breaslă
/ / X = 1 -> nu folosiţi aceeaşi carduri (boxids) de la colegii de breaslă
/ / Implicit 1


M: (1)

/ / M opţiunea -> Mod opţiunea
/ / M: (x)
/ / X = 0 -> Mod locale nu NET
/ / X = 1 -> Mod de NET
/ / Default 0


P: (/ tmp / pmt.tmp)


/ / P opţiunea -> PMT locaţie (Dont folosite cu Linux si Windows)
/ / Trebuie să fie pe reglate astfel incat să canal de tip imagine pot genera acest fişier
/ / (/ Tmp / pmt.tmp) pentru resivers şi imagini care crea acest fişier <- utilizaţi această dacă puteţi
/ / 1/tmp/camd.socket (1) pentru enigma
/ /) (2/tmp/camd.socket pentru enigma 2

[Einstein]

Gobi aste sunt de la Mbox!
Noi discutam de Gbox si mgcamd....

[mondo]

Cam asta face linia O din gbox_cfg:

On Screen Display for the Multysystemcam on COM1/COM2
00 No OSD
01 Display Smartcard messages in Neutrino
02 Display Smartcard messages in Neutrino new nhttpd format
03 Display Smartcard messages in Enigma
mypass (use user=root and pass=mypass for nhttpd)

Acum ramane la latitudinea fiecaruia cum seteaza linia O.

[dyngo]

Multumesc pentru explicatii
am refacut setarile asa cum sunt mai sus si s-a rezolvat oarecum problema cu emulatorul in sensul ca nu mai apar acele scurte blocaje pe imagine dar ar mai fi o problema... partenerii de share nu vad nici un card de la mine(apar cu galben)

[maximuss]

gbox_cfg



# gbox config file created by @tonytr dvbsat.org team

# Trace/Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (don't use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)

# ---- DIT IP AANPASSEN - CHANGE THIS TO YOUR DB IP -------
Z: { 01 12 } ipdream 8024

# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS fr RST detection
# ** 1* Use DCD fr RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
W: { 00 00 } 9600

# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }

# Display ECM messages on Konsole
# 00 don't show any ECM's
# 01 show only valid ECM's
# 02 show valid and bad ECM's with complete data display
C: { 01 }

# Display EMM messages on Konsole
# *0 don't show any EMM's
# *1 show only valid EMM's
# *2 show valid and bad EMM's with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 02 }

# AutoUpdate
# 00 is ignored (default)
# 01 enable AU
# 02 Auto AU !!!!! always use this !!!!!
A: { 01 }

# Key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 02 }

# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this !!!!!
H: { 01 }

# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# mypass (use user=root and pass=mypass for nhttpd)


# ------ DIT IP AANPASSEN - CHANGE THIS TO YOUR DB IP -----
O: { 03 } ipdream user=root pass=paroladream

# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 } 10.0.0.3 2502

# demux, multicam/comport configuration
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
(in the dbox2 the gbox writes directly the CW's, 00 is the
recommended mode ! No drivers are required) use D* ** ONLY if
you have Problems. 0* ** should be prefered !!!
# F* ** ; write CW's in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x*8) invert CTS detection on com2
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
V: { F0 10 }

# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
R: { 00 }

# =============================================================================
# extra options to override default seting in case you expirience Problems,
# normaly these setings are not required.
#
# cpu, api, cw write method
#
# 00 auto
# 01 80X86
# 02 MPC823
# 03 IBM STB04xxx
# 00 auto
# 01 ibm
# 02 api2
# 03 api3
# 00 cw write style = use internal routine (only dbox2)
# 01 cw write style = CA_SET_DESCR type1 (dbox2, vdr)
# 02 cw write style = CA_SET_DESCR type2
# 03 cw write style = CA_SET_DESCR type3
# 04 cw write style = 16 byte /proc/bus/gtx
# 05 cw write style = 4096 byte /proc/bus/gtx, cw offset=0x04D0
# xx write cw in 1st device with index=xx
# yy write cw in 2nd device with index=yy
# 01 means with .index=0 (default)
# 02 means with .index=1
# 03 means with .index=0 and .index=1
# .. any bitwise combination ...
# FF means with all 8 indexes (0-7)
#J: { 01 00 00 01 01 }

# Files, folders, devices
# folder/device comment
#
#F: { 01 } /var/tmp/pmt.tmp // pmt file
#F: { 02 } /var/tmp/emm.info // key update log file
#F: { 03 } /var/tmp/ecm.info // ecm info file
#F: { 04 } /var/tmp/atack.txt // atack info file
#F: { 11 } /var/keys // folder for config files
#F: { 12 } /var/tmp // folder for temporary file
#F: { 13 } /var/tmp // folder for keyfiles
#F: { 21 } /dev/dvb/adapter0/ca0 // ca device
#F: { 22 } /dev/dvb/adapter0/dvr0 // dvr device
#F: { 23 } /dev/dvb/adapter0/demux0 // demux device
#F: { 31 } /dev/dvb/adapter0/ca1 // second ca device to write cw's (reco***ng)
#F: { 41 } /dev/sci0 // STB04xxx slot1
#F: { 42 } /dev/sci1 // STB04xxx slot1
#F: { 43 } /dev/tts/0 // rs232 com1
#F: { 44 } /dev/tts/1 // rs232 com2

# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
#
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 03 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
#F: { 58 } 03 // nds

# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1

# set stay alive ping time in seconds (default is 300)
#F: { A0 } 300


# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
#
#F: { A1 } 0

[maximuss]

mg_cfg


# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 02 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 05 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 08 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } root delbuccio(dreambox_default)

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } ipdream 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted reco***ngs.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 04 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 02 }

[maximuss]

peers.cfg


# sample peer.cfg for gbox client in mgcamd
# syntax the same as in cwshare.cfg,
# you can just copy cwshare.cfg to this file.
# see below for supported tags, others not supported (yet).

# max cards to send ecm too + preffered cards ids (up to 32)
X: { 05 } 1234 ABCD

# max card's distance to use for ecm
I: ( 05 }

# resend after 2 seconds, re-sync (send to all) after 3 seconds
N: { 0 0 0 0 2000 4000 }
# same, but for NDS cards
S: { 0 0 0 0 2000 4000 }

# my host and password
M: { ipdream { parolapeervirtual }}

# peers, unlimited number, but only up to 32 unique ports to listen
# host, port to listen, remote port, password, levels (ignored)
D: { ipdream { 2500 gboxport { parolagbox { A5 A5 }}}}
#D: { ipdream { gboxport 2500 { parolapeervirtual { A5 A5 }}}} # de pus in var/keys/cwshare

# ignore ids
#Y: { 01 02 }
#Y: { 02 03 }

# always save ids
#G: { 03 04 }
#G: { 04 05 }

# virtual cards

V: { 02 { 18 01 20 11 }} # Digi(1W)