Using Infinity Phoenix as reader in Debian

[gemmydo]

Hi there.
I enabled TRY ALL CHIDS : /dev/ttyS0 but than did not fix the issue.
I wonder if it's an entitlement issue?
Below is the dmesg results.

• debian:~# dmesg
• [ 0.000000] Initializing cgroup subsys cpu
• [ 0.000000] Linux version 2.6.26-2-486 (Debian 2.6.26-26lenny1) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Thu Nov 25 01:49:20 UTC 2010
• [ 0.000000] BIOS-provided physical RAM map:
• [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
• [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
• [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
• [ 0.000000] BIOS-e820: 0000000000100000 - 0000000006ff0000 (usable)
• [ 0.000000] BIOS-e820: 0000000006ff0000 - 0000000006ff3000 (ACPI NVS)
• [ 0.000000] BIOS-e820: 0000000006ff3000 - 0000000007000000 (ACPI data)
• [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
• [ 0.000000] 111MB LOWMEM available.
• [ 0.000000] Entering add_active_range(0, 0, 28656) 0 entries of 256 used
• [ 0.000000] Zone PFN ranges:
• [ 0.000000] DMA 0 -> 4096
• [ 0.000000] Normal 4096 -> 28656
• [ 0.000000] Movable zone start PFN for each node
• [ 0.000000] early_node_map[1] active PFN ranges
• [ 0.000000] 0: 0 -> 28656
• [ 0.000000] On node 0 totalpages: 28656
• [ 0.000000] DMA zone: 32 pages used for memmap
• [ 0.000000] DMA zone: 0 pages reserved
• [ 0.000000] DMA zone: 4064 pages, LIFO batch:0
• [ 0.000000] Normal zone: 192 pages used for memmap
• [ 0.000000] Normal zone: 24368 pages, LIFO batch:3
• [ 0.000000] Movable zone: 0 pages used for memmap
• [ 0.000000] DMI 2.3 present.
• [ 0.000000] ACPI: RSDP 000F6AD0, 0014 (r0 CLE266)
• [ 0.000000] ACPI: RSDT 06FF3040, 0028 (r1 CLE266 AWRDACPI 42302E31 AWRD 0)
• [ 0.000000] ACPI: FACP 06FF30C0, 0074 (r1 CLE266 AWRDACPI 42302E31 AWRD 0)
• [ 0.000000] ACPI: DSDT 06FF3180, 37B9 (r1 CLE266 AWRDACPI 1000 MSFT 100000E)
• [ 0.000000] ACPI: FACS 06FF0000, 0040
• [ 0.000000] ACPI: DMI detected: Hewlett-Packard
• [ 0.000000] ACPI: PM-Timer IO Port: 0x4008
• [ 0.000000] Allocating PCI resources starting at 10000000 (gap: 07000000:f8ff0000)
• [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
• [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
• [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
• [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 28432
• [ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
• [ 0.000000] No local APIC present or hardware disabled
• [ 0.000000] mapped APIC to ffffb000 (010e3000)
• [ 0.000000] Enabling fast FPU save and restore... done.
• [ 0.000000] Enabling unmasked SIMD FPU exception support... done.
• [ 0.000000] Initializing CPU#0
• [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
• [ 0.000000] Detected 796.110 MHz processor.
• [ 0.004000] Console: colour VGA+ 80x25
• [ 0.004000] console [tty0] enabled
• [ 0.004000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
• [ 0.004000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
• [ 0.004000] Memory: 103920k/114624k available (1697k kernel code, 10244k reserved, 746k data, 320k init, 0k highmem)
• [ 0.004000] virtual kernel memory layout:
• [ 0.004000] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
• [ 0.004000] vmalloc : 0xc7800000 - 0xfffb1000 ( 903 MB)
• [ 0.004000] lowmem : 0xc0000000 - 0xc6ff0000 ( 111 MB)
• [ 0.004000] .init : 0xc0366000 - 0xc03b6000 ( 320 kB)
• [ 0.004000] .data : 0xc02a85b5 - 0xc0363000 ( 746 kB)
• [ 0.004000] .text : 0xc0100000 - 0xc02a85b5 (1697 kB)
• [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
• [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
• [ 0.084345] Calibrating delay using timer specific routine.. 1594.79 BogoMIPS (lpj=3189580)
• [ 0.084456] Security Framework initialized
• [ 0.084475] SELinux: Disabled at boot.
• [ 0.084489] Capability LSM initialized
• [ 0.084531] Mount-cache hash table entries: 512
• [ 0.084872] Initializing cgroup subsys ns
• [ 0.084885] Initializing cgroup subsys cpuacct
• [ 0.084895] Initializing cgroup subsys devices
• [ 0.084947] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
• [ 0.084959] CPU: L2 Cache: 64K (32 bytes/line)
• [ 0.084996] CPU: Centaur VIA Nehemiah stepping 08
• [ 0.085018] Checking 'hlt' instruction... OK.
• [ 0.105107] Freeing SMP alternatives: 0k freed
• [ 0.105121] ACPI: Core revision 20080321
• [ 0.117060] ACPI: setting ELCR to 0200 (from 8e20)
• [ 0.119605] net_namespace: 652 bytes
• [ 0.119633] Booting paravirtualized kernel on bare hardware
• [ 0.120197] NET: Registered protocol family 16
• [ 0.120915] EISA bus registered
• [ 0.120962] ACPI: bus type pci registered
• [ 0.127207] PCI: PCI BIOS revision 2.10 entry at 0xfa6a0, last bus=1
• [ 0.127219] PCI: Using configuration type 1 for base access
• [ 0.127256] Setting up standard PCI resources
• [ 0.143237] ACPI: EC: Look up EC in DSDT
• [ 0.157929] ACPI: Interpreter enabled
• [ 0.157947] ACPI: (supports S0 S5)
• [ 0.157995] ACPI: Using PIC for interrupt routing
• [ 0.171389] ACPI: PCI Root Bridge [PCI0] (0000:00)
• [ 0.172042] pci 0000:00:11.0: quirk: region 4000-407f claimed by vt8235 PM
• [ 0.172058] pci 0000:00:11.0: quirk: region 5000-500f claimed by vt8235 SMB
• [ 0.172474] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
• [ 0.210493] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *15
• [ 0.211121] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *5
• [ 0.211755] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
• [ 0.212415] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *10 11 12)
• [ 0.212909] Linux Plug and Play Support v0.97 (c) Adam Belay
• [ 0.213008] pnp: PnP ACPI init
• [ 0.213039] ACPI: bus type pnp registered
• [ 0.222047] pnp: PnP ACPI: found 12 devices
• [ 0.222060] ACPI: ACPI bus type pnp unregistered
• [ 0.222076] PnPBIOS: Disabled by ACPI PNP
• [ 0.222898] PCI: Using ACPI for IRQ routing
• [ 0.223422] ACPI: RTC can wake from S4
• [ 0.223515] system 00:00: iomem range 0xc8000-0xcbfff has been reserved
• [ 0.223530] system 00:00: iomem range 0xda000-0xdbfff has been reserved
• [ 0.223545] system 00:00: iomem range 0xf0000-0xfbfff could not be reserved
• [ 0.223560] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
• [ 0.223575] system 00:00: iomem range 0x6ff0000-0x6ffffff could not be reserved
• [ 0.223591] system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
• [ 0.223606] system 00:00: iomem range 0x0-0x9ffff could not be reserved
• [ 0.223620] system 00:00: iomem range 0x100000-0x6feffff could not be reserved
• [ 0.223636] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
• [ 0.223651] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
• [ 0.223684] system 00:02: ioport range 0x4000-0x407f has been reserved
• [ 0.223698] system 00:02: ioport range 0x5000-0x500f has been reserved
• [ 0.223738] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
• [ 0.255102] PCI: Bridge: 0000:00:01.0
• [ 0.255112] IO window: disabled.
• [ 0.255127] MEM window: 0xec000000-0xedffffff
• [ 0.255140] PREFETCH window: 0x00000000e8000000-0x00000000ebffffff
• [ 0.255177] PCI: Setting latency timer of device 0000:00:01.0 to 64
• [ 0.255255] NET: Registered protocol family 2
• [ 0.255564] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
• [ 0.256309] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
• [ 0.256432] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
• [ 0.256506] TCP: Hash tables configured (established 4096 bind 4096)
• [ 0.256517] TCP reno registered
• [ 0.256746] NET: Registered protocol family 1
• [ 0.257193] checking if image is initramfs...&lt7>Switched to high resolution mode on CPU 0
• [ 1.338457] it is
• [ 2.558591] Freeing initrd memory: 6048k freed
• [ 2.560002] audit: initializing netlink socket (disabled)
• [ 2.560085] type=2000 audit(1315965633.560:1): initialized
• [ 2.560352] Total HugeTLB memory allocated, 0
• [ 2.560543] VFS: Disk quotas dquot_6.5.1
• [ 2.560645] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
• [ 2.560756] msgmni has been set to 214
• [ 2.561153] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
• [ 2.561168] io scheduler noop registered
• [ 2.561177] io scheduler anticipatory registered
• [ 2.561186] io scheduler deadline registered
• [ 2.561220] io scheduler cfq registered (default)
• [ 2.561255] PCI: VIA PCI bridge detected.Disabling DAC.
• [ 2.561357] pci 0000:01:00.0: Boot video device
• [ 2.562430] isapnp: Scanning for PnP cards...
• [ 2.916929] isapnp: No Plug & Play device found
• [ 2.925919] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
• [ 2.926151] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
• [ 2.927226] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
• [ 2.931899] brd: module loaded
• [ 2.932246] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
• [ 2.932812] serio: i8042 KBD port at 0x60,0x64 irq 1
• [ 2.932831] serio: i8042 AUX port at 0x60,0x64 irq 12
• [ 2.933317] mice: PS/2 mouse device common for all mice
• [ 2.933714] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
• [ 2.933755] rtc0: alarms up to one year, y3k
• [ 2.934081] EISA: Probing bus 0 at eisa.0
• [ 2.934120] Cannot allocate resource for EISA slot 4
• [ 2.934130] Cannot allocate resource for EISA slot 5
• [ 2.934159] EISA: Detected 0 cards.
• [ 2.934170] cpuidle: using governor ladder
• [ 2.934180] cpuidle: using governor menu
• [ 2.934196] No iBFT detected.
• [ 2.935962] TCP cubic registered
• [ 2.935974] NET: Registered protocol family 17
• [ 2.935994] Using IPI Shortcut mode
• [ 2.936477] registered taskstats version 1
• [ 2.936908] rtc_cmos 00:05: setting system clock to 2011-09-14 02:00:34 UTC (1315965634)
• [ 2.938444] Freeing unused kernel memory: 320k freed
• [ 2.957567] input: AT Translated Set 2 keyboard as /class/input/input0
• [ 3.378846] ACPI: PNP0C0B:00 is registered as cooling_device0
• [ 3.378871] ACPI: Fan [FAN] (on)
• [ 3.402080] ACPI: CPU0 (power states: C1[C1] C2[C2])
• [ 3.402218] ACPI: ACPI0007:00 is registered as cooling_device1
• [ 3.402236] ACPI: Processor [CPU0] (supports 2 throttling states)
• [ 3.408256] ACPI: LNXTHERM:01 is registered as thermal_zone0
• [ 3.408624] ACPI: Thermal Zone [THRM] (-248 C)
• [ 5.021954] Uniform Multi-Platform E-IDE driver
• [ 5.021975] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
• [ 5.190591] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
• [ 5.192086] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
• [ 5.192099] PCI: setting IRQ 11 as level-triggered
• [ 5.192112] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
• [ 5.192135] via-rhine 0000:00:12.0: VIA VLink IRQ fixup, from 15 to 11
• [ 5.197054] eth0: VIA Rhine II at 0x1e400, 00:17:08:5e:2f:d1, IRQ 11.
• [ 5.197783] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
• [ 5.230384] usbcore: registered new interface driver usbfs
• [ 5.230472] usbcore: registered new interface driver hub
• [ 5.230613] usbcore: registered new device driver usb
• [ 5.245343] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
• [ 5.245358] PCI: setting IRQ 10 as level-triggered
• [ 5.245371] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
• [ 5.245412] ehci_hcd 0000:00:10.3: EHCI Host Controller
• [ 5.245708] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
• [ 5.245816] ehci_hcd 0000:00:10.3: irq 10, io mem 0xee000000
• [ 5.250278] USB Universal Host Controller Interface driver v3.0
• [ 5.256139] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
• [ 5.256433] usb usb1: configuration #1 chosen from 1 choice
• [ 5.256548] hub 1-0:1.0: USB hub found
• [ 5.256584] hub 1-0:1.0: 4 ports detected
• [ 5.360495] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
• [ 5.360512] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
• [ 5.360524] usb usb1: Product: EHCI Host Controller
• [ 5.360534] usb usb1: Manufacturer: Linux 2.6.26-2-486 ehci_hcd
• [ 5.360544] usb usb1: SerialNumber: 0000:00:10.3
• [ 5.360737] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
• [ 5.360760] uhci_hcd 0000:00:10.0: VIA VLink IRQ fixup, from 15 to 11
• [ 5.360800] uhci_hcd 0000:00:10.0: UHCI Host Controller
• [ 5.360883] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
• [ 5.360932] uhci_hcd 0000:00:10.0: irq 11, io base 0x0000ea00
• [ 5.361302] usb usb2: configuration #1 chosen from 1 choice
• [ 5.361415] hub 2-0:1.0: USB hub found
• [ 5.361448] hub 2-0:1.0: 2 ports detected
• [ 5.464462] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
• [ 5.464479] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
• [ 5.464492] usb usb2: Product: UHCI Host Controller
• [ 5.464501] usb usb2: Manufacturer: Linux 2.6.26-2-486 uhci_hcd
• [ 5.464512] usb usb2: SerialNumber: 0000:00:10.0
• [ 5.465975] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
• [ 5.465988] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
• [ 5.466011] uhci_hcd 0000:00:10.1: VIA VLink IRQ fixup, from 5 to 11
• [ 5.466053] uhci_hcd 0000:00:10.1: UHCI Host Controller
• [ 5.466160] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
• [ 5.466206] uhci_hcd 0000:00:10.1: irq 11, io base 0x0000eb00
• [ 5.466578] usb usb3: configuration #1 chosen from 1 choice
• [ 5.466686] hub 3-0:1.0: USB hub found
• [ 5.466719] hub 3-0:1.0: 2 ports detected
• [ 5.568440] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
• [ 5.568458] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
• [ 5.568470] usb usb3: Product: UHCI Host Controller
• [ 5.568480] usb usb3: Manufacturer: Linux 2.6.26-2-486 uhci_hcd
• [ 5.568490] usb usb3: SerialNumber: 0000:00:10.1
• [ 5.569542] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:11.1
• [ 5.569604] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
• [ 5.569627] VIA_IDE 0000:00:11.1: VIA VLink IRQ fixup, from 255 to 11
• [ 5.569669] VP_IDE: not 100% native mode: will probe irqs later
• [ 5.569709] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
• [ 5.569725] VP_IDE: IDE port disabled
• [ 5.569742] ide0: BM-DMA at 0xe900-0xe907
• [ 5.569764] Probing IDE interface ide0...
• [ 5.912109] usb 2-2: new low speed USB device using uhci_hcd and address 2
• [ 5.984177] hda: HyperDisk DOM, ATA DISK drive
• [ 6.097206] usb 2-2: configuration #1 chosen from 1 choice
• [ 6.100440] usb 2-2: New USB device found, idVendor=104f, idProduct=0001
• [ 6.100455] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
• [ 6.100466] usb 2-2: Product: Infinity USB
• [ 6.100475] usb 2-2: Manufacturer: WB Electronics
• [ 6.320215] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
• [ 6.320300] hda: UDMA/100 mode selected
• [ 6.320394] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
• [ 6.332108] No dock devices found.
• [ 6.362990] SCSI subsystem initialized
• [ 6.617021] libata version 3.00 loaded.
• [ 7.110050] hda: max request size: 128KiB
• [ 7.110067] hda: 3767904 sectors (1929 MB) w/1KiB Cache, CHS=3738/16/63
• [ 7.121853] hda: cache flushes supported
• [ 7.122008] hda: hda1 hda2 < hda5 >
• [ 7.188264] Marking TSC unstable due to: TSC halts in idle.
• [ 7.404351] PM: Starting manual resume from disk
• [ 7.464609] kjournald starting. Commit interval 5 seconds
• [ 7.464609] EXT3-fs: mounted filesystem with ordered data mode.
• [ 8.571329] udevd version 125 started
• [ 11.855181] input: PC Speaker as /class/input/input1
• [ 14.018613] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
• [ 14.090350] Linux agpgart interface v0.103
• [ 14.196872] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
• [ 14.268407] agpgart: Detected VIA CLE266 chipset
• [ 14.272840] agpgart: AGP aperture is 64M @ 0xe4000000
• [ 14.702919] NET: Registered protocol family 23
• [ 16.319399] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
• [ 16.444664] parport_pc 00:09: reported by Plug and Play ACPI
• [ 16.444732] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
• [ 16.502088] Error: Driver 'pcspkr' is already registered, aborting...
• [ 17.042567] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
• [ 17.042584] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
• [ 17.042753] PCI: Setting latency timer of device 0000:00:11.5 to 64
• [ 17.384984] input: Power Button (FF) as /class/input/input3
• [ 17.456339] ACPI: Power Button (FF) [PWRF]
• [ 17.456611] input: Power Button (CM) as /class/input/input4
• [ 17.485151] ACPI: Power Button (CM) [PWRB]
• [ 22.453377] Adding 144544k swap on /dev/hda5. Priority:-1 extents:1 across:144544k
• [ 22.557022] EXT3 FS on hda1, internal journal
• [ 23.158858] loop: module loaded
• [ 24.604985] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
• [ 26.833499] NET: Registered protocol family 10
• [ 26.835027] lo: Disabled Privacy Extensions
• [ 28.975276] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
• [ 37.784037] eth0: no IPv6 routers present
• debian:~#

[fery21]

You hawe used tutorial of install ?

hear

you driver not work insmod

[gemmydo]

Yes install correctly no errors. ALL channels clear except sly movies and sports.
If I put my card in the dreambox the movies and sports clear as they should.
I have also tried reader on different frequencies but 5.58 and 5.68 make no difference. 6.00 doesn't clear at all.
It is odd that only the movies and sports won't clear so it can't be a driver issue as if the driver was incorrect the reader would not work.

insmod is used to install modules, what modules am I missing?

Any other ideas?

[gemmydo]

Simple fix, need to check the below are on the same device.
SERIAL READER : /dev/ttyS0
BOXKEY: /dev/ttyS0