Buna.
Am un router topex cu openwrt.Conform tutorialul lui Rsofty am facut sa booteaza de pe stick si am instalat cccam.
Cineva are un tutorial pentru instalare samba si mondtare hdd extern (NTFS)
Multumesc
Topex cu openwrt cu boot de pe stick
Buna.
Am un router topex cu openwrt.Conform tutorialul lui Rsofty am facut sa booteaza de pe stick si am instalat cccam.
Cineva are un tutorial pentru instalare samba si mondtare hdd extern (NTFS)
Multumesc
Instalare SAMBA
root@OpenWrt:/# opkg update
root@OpenWrt:/# opkg install luci-app-samba
Installing luci-app-samba (0.8.8-1) to root...
Downloading http://downloads.openwrt.org/kamikaz...8-1_mipsel.ipk
Connecting to 10.1.1.1:8080 (10.1.1.1:8080)
luci-app-samba_0.8.8 100% |*************************************************************************************************** ******| 2866 --:--:-- ETA
Installing samba3 (3.0.24-2) to root...
Downloading http://downloads.openwrt.org/kamikaz...4-2_mipsel.ipk
Connecting to 10.1.1.1:8080 (10.8.39.5:8080)
samba3_3.0.24-2_mips 100% |*************************************************************************************************** ******| 456k 00:00:00 ETA
Installing libpthread (0.9.29-14.3) to root...
Downloading http://downloads.openwrt.org/kamikaz...4.3_mipsel.ipk
Connecting to 10.1.1.1:8080 (10.1.1.1:8080)
libpthread_0.9.29-14 100% |*************************************************************************************************** ******| 19340 --:--:-- ETA
Configuring libpthread
Configuring luci-app-samba
Configuring samba3
preluat de pe alt forum, autorul tutorialului este tivcol
In legatura cu hdd exter partitionat NTSF, eu ti-as recomanda sal partitionezi EXT3, findca openwrt kamikaze (kernel 2.4) NTSF poate doar sal citesca nu si sa scrie (este READ ONLY, RO).
Dupa cum ai scris presupun ca ai instalat openwrt kamikaze kernel 2.4
Mersi Sorin.
Atunci de aia nu vede pe hard.Si o problema ca samba nu a aparut in webinterface.
Sorin,
Daca fac fat si nu ext3.O sa fie tot read only?
Primesc eroarea urmatoare cand dau comanda dmesg din putty.Totul am facut conform tutorial.
NU stiti de ce?
usb.c: USB disconnect on device 01:02.0-1.3 address 6
hub.c: new USB device 01:02.0-1.3, assigned address 7
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 7
usb.c: USB disconnect on device 01:02.0-1.3 address 7
hub.c: new USB device 01:02.0-1.3, assigned address 8
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 8
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
FAT: bogus logical sector size 0
UDP: bad checksum. From 78.174.30.222:8403 to 192.168.0.3:41534 ulen 106
usb.c: USB disconnect on device 01:02.0-1.3 address 8
hub.c: new USB device 01:02.0-1.3, assigned address 9
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 9
Nu stie nimeni raspunsul?
Posting Permissions
Reply With Quote