Oscam - setari deosebite

**lao** · 13-04-11, 15:10

Fiind un subiect la moda si considerand ca oscam a ajuns la maturitate, deschid acest thread cu intentia de a aprofunda acest soft, ma refer la alte setari decat cele clasice.
De exemplu :
Daca cineva a folosit la reader

device
parameter is required

<device|bus:device|device:slot>|Serial:Reader serial|<ip|host
name>,<port>[,<lport>]|pcsc|<0|1>|constantcw

device: device name (eg myreader)

bus:device: bus name and device name of the Smartreader+
(get the names with lsusb 'Bus' and 'Device')

device:slot: device name and slot number sc8in1 [1-8]
(only one SC8in1 reader supported)

serial: serial number of Smartreader+
(get the serial number while starting OSCam)

lport: remapping to local port

PCSC: number of PCSC reader, starting with 0

0|1: for Coolstream HD-1 STB only: select reader 0 or reader 1

serial sau lport, etc
Sau altceva in loc de cd

detect
parameter depends on setup/programversion

status detect of card is in

Detect = CD (Carrier Detect) - default -
Detect = DSR (Data Set Ready)
Detect = CTS (Clear To Send)
Detect = RING (Ring Indicator)
Detect = NONE (detect switched off, but signal "card is in"
Detect = gpio1 ... gpio7 (neu fur mipsel-uclibc)

Sau modalitati de conectare ale oscamului la diverse device externe....
ETC....
Intelegeti voi, e despre tot ce nu e "cale batatorita"

**lao** · 08-10-12, 22:17

Cunoaste cineva unde trebuie modificat in surse, sau macar care este fisierul, ca la READERS/Show Graphs sa apara liniile de marcaj si altfel decat:
250 ms, 500 ms, 750ms etc
Poate vreau sa vad din suta-n suta...

**neutrin** · 08-10-12, 22:52

In fisierul module-webif-pages.c, incearca sa te joci cu valorile din macro-ul TPLGRAPH, care defineste functia javascript switch_interval(). Ma astept sa trebuiasca sa faci si alte ajustari, nu m-am uitat ce strategie folosesc pentru afisare.

**Diablo1** · 08-10-12, 23:16

@lao
Adica la device sai dai altä denumire pentru reader ?
device = /dev/Digi1802

**lao** · 08-10-12, 23:37

Nu, la asta ma refer:

Am modificat aici

Code:

function switch_interval() {\n\
    if (interval<=1000) {\n\
        interval -= 250;\n\

Am pus 100 in loc de 250 dar nu e deajuns, m-am cam repezit in loc sa citesc mai mult ce e pe acolo

Mai sapam...

**lao** · 27-01-13, 13:11

Pentru cine doreste sa vada mai aerisit ...

Adica, in loc de

2013/01/27 12:49:30 5CD0C8 c vu (0B00&000000/0000/1008/7A:2B129C0313656FBEEADB35B2848B093E): found (366 ms) by lx (P/1/1/2) - BBC HD

Sa apara asa

2013/01/27 12:52:40 5CD0C8 c vu (0B00&000000/1008/7A): found (364 ms) by lx (P/1/1/2) - BBC HD

Setati in (webif) config/global

Code:

ecmfmt                        = c&p/s/l

Sau, daca doriti un log mai lung sau mai scurt in pagina status, modificati valoarea

Code:

loghistorysize                = 4096

Nu e cine stie ce, sunt documentate deja in oscam, dar... nu prea sunt studiate chestiile astea

Link

**Znuff** · 04-02-13, 07:00

Originally Posted by lao

Nu, la asta ma refer:

Am modificat aici

Code:

function switch_interval() {\n\
    if (interval<=1000) {\n\
        interval -= 250;\n\

Am pus 100 in loc de 250 dar nu e deajuns, m-am cam repezit in loc sa citesc mai mult ce e pe acolo

Mai sapam...

1. Seteaza un template directory. Gen /usr/local/etc/tpl
2. Viziteaza http://ip

ort/savetemplates.html
3. Vezi fisierul GRAPH.tpl
4. Sterge totul in afara de GRAPH.TPL (asta daca nu ai chef sa modifici si altceva, binenteles)

Editeaza fisierul si cauta linia:

Code:

   <path id='graph_grid' class='graph_grid' d='M 2 75 L 800 75 M 2 150 L 800 150 M 2 225 L 800 225'/>

Ca sa intelegi codul SVG:

M 2 75 L 800 75
M 2 150 L 800 150
M 2 225 L 800 225

Astea sunt cele 3 linii ale tale. E un sistem de coordonate X Y. M inseamna "move to" (du-te la) punctul 2,75. L Inseamna "traseaza o linie de la punctul curent (2,10) pana la 800 cu 75".

Graficul are o dimensiune de 800x300 si 0,0 corespunde coltului stanga-sus.

Deci Y=75 == 750ms, Y=150 == 500ms, Y=225 == 250ms. Deci 75px == 250ms.

Pentru un grid din 100 in 100ms folosim un "pas" de 30 pixeli.

Code:

<path id='graph_grid' class='graph_grid' d='M 2 30 L 800 30 M 2 60 L 800 60 M 2 90 L 800 90 M 2 120 L 800 120 M 2 150 L 800 150 M 2 180 L 800 180 M 2 210 L 800 210 M 2 240 L 800 240 M 2 270 L 800 270'/>

Nu sunt sigur acum cum functioneaza treaba, dar cand timpul de raspuns al unui reader trece de 1000ms, scara se dubleaza, si in loc sa arate de la 0 la 1000ms, va arata de la 0 la 2000, fara a redesena gridul, dar textul (250/500/750ms) se va actualiza cu noile valori (500/1000/1500).

Tine minte ca nu este intotdeauna necesar/recomandat sa editezi codul sursa. In cazul de fata daca editezi template-ul esti mai castigat

---------- Post added at 07:00 ---------- Previous post was at 06:44 ----------

Bun,

Si daca tot ne-am apucat de ceva, hai sa si terminam ca oricum nu am somn.

Hai sa "rezolvam" si "legenda" graficului:

Cautam liniile astea:

Code:

   <text id='graph_grid_txt3' class='graph_grid_txt' x='800' y='223'>-</text>
   <text id='graph_grid_txt2' class='graph_grid_txt' x='800' y='148'>-</text>
   <text id='graph_grid_txt1' class='graph_grid_txt' x='800' y='73'>-</text>

Code:

   SVGDoc.getElementById('graph_grid_txt1').firstChild.data = 3*rmax/4 + 'ms'
   SVGDoc.getElementById('graph_grid_txt2').firstChild.data = 2*rmax/4 + 'ms';
   SVGDoc.getElementById('graph_grid_txt3').firstChild.data = rmax/4 + 'ms';

Si le inlocuim cu astea:

Code:

   <text id='graph_grid_txt9' class='graph_grid_txt' x='800' y='268'>-</text>
   <text id='graph_grid_txt8' class='graph_grid_txt' x='800' y='238'>-</text>
   <text id='graph_grid_txt7' class='graph_grid_txt' x='800' y='208'>-</text>
   <text id='graph_grid_txt6' class='graph_grid_txt' x='800' y='178'>-</text>
   <text id='graph_grid_txt5' class='graph_grid_txt' x='800' y='148'>-</text>
   <text id='graph_grid_txt4' class='graph_grid_txt' x='800' y='118'>-</text>
   <text id='graph_grid_txt3' class='graph_grid_txt' x='800' y='88'>-</text>
   <text id='graph_grid_txt2' class='graph_grid_txt' x='800' y='58'>-</text>
   <text id='graph_grid_txt1' class='graph_grid_txt' x='800' y='28'>-</text>

Code:

   SVGDoc.getElementById('graph_grid_txt1').firstChild.data = 9*rmax/10 + 'ms'
   SVGDoc.getElementById('graph_grid_txt2').firstChild.data = 8*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt3').firstChild.data = 7*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt4').firstChild.data = 6*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt5').firstChild.data = 5*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt6').firstChild.data = 4*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt7').firstChild.data = 3*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt8').firstChild.data = 2*rmax/10 + 'ms';
   SVGDoc.getElementById('graph_grid_txt9').firstChild.data = rmax/10 + 'ms';

Si... gata :-)

Edit: Si fisierul gata facut: http://z.linge-ma.ws/GRAPH.tpl (dati si voi cu Save As...)

**kosar** · 04-05-13, 19:50

Daca linia N vrei s-o folosesti cu 256 in spate in cccam, trebuie sa ai versiune mai mica de cccam de 2.13.

Altundeva n-am idee unde ai vrea s-o folosesti cu 256, doar acolo e functional.

**lao** · 04-05-13, 19:58

A devenit setare deosebita chestia asta cu 256?
Interesant...

O sa incerc si eu minunea

**lao** · 30-05-13, 18:22

Desi am zis ceva si in alt post, o sa aprofundez problema aici
A aparut un patch pentru oscam, trebuie compilat oscam cu acest patch

http://sateliti.info/attachment.php?...2&d=1369920557

Care face ca oscam cu dvbapi sa deschida mai repede. Aproape ca FTA.
Deci acest patch nu actioneaza decat asupra DVBAPI, n-are treba cu altceva, nu imbunatateste liniile.
Doar face lumina mai repede pe ecran.

Code:

[dvbapi]
enabled                       = 1
au                            = 1
pmt_mode                      = 6
request_mode                  = 0
delayer                       = 0
user                          = vuduo
boxtype                       = dreambox

Oscam.dvbapi trebuie redenumit altfel sau sters. In caz ca doriti sa-l folositi in continuare e ceva de munca

Code:

P: 0100:000068 # Cyfra+
P: 0100:000065 # Cyfra+ VOD
P: 1803:000000 # Polsat
P: 0d03:000004 # Sky Link
P: 0100:00006a # C+ NED
P: 0100:00006c # TV Vlaanderen
P: 1810:000000 # D+ nagra
P: 0100:004106 # D+ seca
P: 09cd:000000 # sky it
P: 093b:000000 # sky it
P: 0919:000000 # sky it
P: 090f:000000 # Viasat
P: 093e:000000 # Viasat
I:0

Problema e ca ce nu e trecut cu P nu mai deschide in veci, poate sa fie si card local.

---------- Post added at 18:22 ---------- Previous post was at 16:41 ----------

A aparut dvbapi85 si merge bine
http://sateliti.info/attachment.php?...4&d=1369927023

Link catre topicul streamboard

din comentariile de acolo

works
good job ;-)
well done

ready for trunk ;-)

**lao** · 05-06-13, 20:40

Dupa nenumarate versiuni si teste, azi a fost inglobat in trunk

Timestamp: 06/05/13 18:40:44 (less than one hour ago)
Author:theparasol
Message:

Added CA PMT Server support (PMT6: PIP on DM7025 reported to have issues)
Revised the ecm requesting and ecm response handling
EMM start and handling changed (now emm on expired cards and FTA channels)
Revised the handling of controlwords (using wrong index should not happen anymore)

Reopenonzap:

Some users report that VU+ boxes needs this checked otherwise issues after a timeout response

This patch is checked by many regular users of streamboard and considered trunk ready.

**stargate** · 06-06-13, 00:00

Am pus eu OSCam 8680 pe Amiko Alien si deschide mai rapid dar si la fel de rapid intra in balarii si nu mai deschide apoi nimic ( nici din local ) si imi da eroarea asta

Code:

2013/06/05 23:59:37 2A157C58 c [DVBAPI] oscam.dvbapi found applying valid parsed rules!
2013/06/05 23:59:37 2A157C58 c [DVBAPI] Demuxer #0 trying to descramble PID #0 CAID 0B02 PROVID 000000 ECMPID 15E4
2013/06/05 23:59:37 2A157C58 c ERROR: Can't open device /dev/dvb/adapter0/demux0 (errno=24 Too many open files)
2013/06/05 23:59:37 2A157C58 c ERROR: Could not start demux filter (errno=9 Bad file descriptor)

**lao** · 30-05-13, 16:31

(Aici urc eu atasamentele mele mici, pentru ca aici ma lasa)

**lao** · 30-05-13, 18:18

dvbapi85

**klausz** · 07-06-13, 09:58

Exista vreo posibilitate ca un user conectat la server oscam prin cccam sau altceva sa traga ecm-uri fara ca oscam sa raporteze acest lucru?

Sent from my GT-I9300 using Tapatalk 4 Beta

Thread: Oscam - setari deosebite

Thread Tools

Display

Hybrid View

Oscam - setari deosebite

Atasamentele mele

Posting Permissions