Samsung dsr9500
Reply With Quoteasta e ce am incercat de cele mai multe ori...
la inceput cu hiper terminalul, dupa ce dau dupa ce dau drumul la rec, incepe sa se incarce loading cccccc si dupa aia dau send, si imi da eroare...
If you have problems maybe uploading the new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well, kill your Sammy at the back and then... Here's a copy of my post from other threads:
Quote:
When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.
Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.
If it times-out - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!
Choose the EMU you want to upload. Then Settings list. Then RAM. Then CAID list.
Enjoy! Hopefully!
Here is the Papagen's contribution:
________________________________________
Uploading Software Into Samsung Using Hyper Terminal
Start/Program/Accessories/Communications/Hyper Terminal
Setting the Hyper Terminal
1. Start Hyper Terminal.
2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
3. In the new opened window, near "Connect using" choose "Direct to COM1, afterwards click OK.
Port Settings
1. Bits per second : 115200
2. Data Bit : 8
3. Parity : NONE
4. Stop Bit : 1
5. Flow Control : Hardware
Click OK
Uploading software into Hyper Terminal
1. Choose TRANSFER
2. Then choose SEND FILE ....
3. BROWSE - select from hard drive the desired version of software (e.g. DSR9500_Eurocam_5-1_EMU_vXX.bin)
4. Choose 1KXmodem for Protocol
Don't press the button "Send", you will do it subsequently.
After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).
The things you have to do are :
1. Disconnect your Samsung using the switch on the rear.
2. In the front of Samsung keep pressed the "right arrow" (volume up).
3. Power up your Samsung on the rear switch and keep constantly pressed "right arrow" (volume up).
Keep the "arrow" pressed until the "3-01" appears on the display,
from that moment the computer will show "............................... Loading"
4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
With clicking on "Send" starts the uploading the software into Samsung.
Don't be hasty! Wait for entire process to terminate.
Process is terminated when on the Samsung a clock appears.
Afterwards insert some of the cards with Conax emulation without keys.
That was it.
If you have done all properly, there is a desired version of software in you Samsung.
The easiest way to verify if upload succeeded : Menu/System properties/System information.
Old versions of the EMU software has the version number 118 and new have 133.
HOW TO FOR SAMMY WITH GOLD EMU BY MAHDI
1) Samsung DSR 9500 VIA CI [HW 504, Loader 500 or 501 can use both but 4.3 or later] - put it on Standby
2) Connect to the PC via straight serial cable
3) Start Samsung DSR Studio 1.2 Editor by MAHDI
4) Choose FW Loader TAB
5) Choose Serial Port
6) Click on Send FW and then choose which EMU [and it's away, racing...]
7) Wait untill you see the clock on Sammy Display
8) Start Sammy [on FTA channel, just in case], check it, then put it on Standby
9) Click on RAM Editor Tab in the Samsung DSR 9500 Studio Editor by MAHDI
10) Choose Serial Port, then Open File, then click on Write and wait for the clock again
11) If you see "Insert smartcard" message, just re-start Sammy
12) At this point I would [and I am going to]
Menu -> Channel organising -> Delete all channels and then
Menu -> Installation -> Manual Scanning and do your own settings list... But it may not be necessary, just rescan Manually if you do not get some channels/transponders!
13) Gonna experiment with various cards/CAMs to see what works and how...
14) Must sort out the GBox and Card Sharing bits... [SEE BELLOW!!!]
15) More than anything must have fun doing it!
Mahdi, m8, a suggestion:
We could do with a bit of an editor/controls of all the CS options [2 pieces of SW]. Both as a Server via a programmer in the Phoenix mode and as a Client.
THANKING YOOOOOUUUUUUUUUUUUUUUUUUUUUUU!!!!!!!!!!!!!!!
MAHDI FOR PRESIDENT!!!
Thanx to Dalen, my translation...
How to change a key via Remote...
Quote:
1. Choose a channel to check if the key is OK
2. Get into the receiver's Gold Emu Menu (press 0 + Menu on your Remote)
3. Choose the Key Editor Menu
4. Choose a system of encryption (like Nagra for D+)
5. Choose the right IDENT (for D+ it's 4101)
6. When you choose the right one press on the OK button
7. In the window for putting the key in first
7a. we write the IDENT, then
7b. the INDEX and then
7c. the first 16 signs
8. Repeat all that and put in the next 16 signs
9. If it's all cool the picture should appear... colours!!!
10. Press on Exit button
Originally Posted by laleauaneagra13
