Vu+ SOLO

[dingo31]

sigur merita banii - are deja imaginea vti 3.0 , tuner p&p c/t optional, 512 MB, etc etc ....:

HighDistinctions of Vu+ UNO
• State-of-theart pluggable tuner system supporting DVB-S2 and DVB-C/T
• Powerful400MHz CPU supporting OpenGL 1.0
• Enhancedmemory size of 512MB ready for any kind of future applications.
• Temperaturesensor based automatic FAN speed control guaranteeing the stealthoperation.
• Extremelylow deep standby power consumption of under 0.5W
• Modelessuniversal remote control
• UnfailingH/W and S/W.
MainFeatures
• HDPVR with single tuner
• Pluggabletuner system supporting DVB-S2 or DVB-C/T.
• 400MHzCPU supporting OpenGL 1.0
• LinuxOperating System
• 12digit VFD display
• 2x Smartcard-Reader
• 2x Common Interface
• 3x USB2.0
• 10/100MbitEthernet Interface
• AdvanceEPG (electronic program guide)
• Fullautomatic service scan
• Multimediaplug-in support
• VariousOSD skin supported
• Lowdeep standby power consumption under 0.5 W
TechnicalSpecifications
Vu+Technical Specifications
FrontPanel
• Display:12-digit Dot Matrix VFD display with status icons displaying channelnames and program information
• Smartcard slot: 2
• CommonInterface: 2
• USB2.0: 1
• Key:Ch+/-, Vol+/-, Standby
RearPanel
• Powerswitch: 1
• Sat-IFinput/output: 2 x F-type socket
• ConnectionTV: 1 x Scart socket
• Videooutput (analogue): 1 x Cinch-socket
• Video/audiooutput (digital): 1 x HDMI
• Audiooutput (analogue): 2 x Cinch socket
• Audiooutput (digital): Standard optical (SPDIF)
• USB2.0: 2
• eSATA:1
• Ethernet:1
• RS232: 1

Power
• Mainsvoltage: AC100-240V / 50-60Hz
• Powerconsumption: (Max./typ. operation/stand-by): 42/17/0.5W
RF
• RFrange: 950-2,150 MHz
• Modulation,FEC, de-multiplexer: DVB-S/DVB-S2 standard
Video
• Videoresolution: CCIR 601 (720 x 576 lines), 576p, 720p, 1080i
• Videodecoding: MPEG-2, MPEG-4 compatible
• Inputdata rate: 2-45 MSymb/s
• S/N:> 53 dB
Decoding
• Decodingolby Digital, MPEG-4 (AAC-HE), MPEG-1, Layer 1, 2 and 3
• Samplingrate: 32/4.1/48 kHz
• S/N:> 65 dB
LNB
• LNBsupply (horiz./vert.): 14/18V / Max.400mA
• Controlsignal: 22kHz ; ToneBurst ; DiSEqCTM1.0/1.1/1.2
General
• Dimensions(W x H x D): 340 x 272 x 60 mm
• Weight(without HDD): 2.35kg (Without HDD)

[dingo31]

dupa imaginea vti 3.0 nu am mai reusit sa instalez imagini versiuni mai noi, nici vti, nici bh?
imagine mai vechi de vti 3.0 si bh 1.7.3 se instaleaza fara probleme, la versiuni mai noi se blocheaza???~!!!!
care ar fi problema????????

[SuperSonic]

Ai facut update de bootloader ?

[dingo31]

multumesc, asta era

[R3al.dx]

Salutari !
Am un Solo cu imagine Vti 5.1. 16.02.013 . Nu am schimbat imaginea de peste 2 ani .
Am incercat sa instalez imagini mai noi, insă nu reusesc .
Orice ajutor este binevenit .

[mondo]

1.Download image zip file for your Vu+ model;
2.Unzip the zip file and you will have a folder named vuplus and under the folder, you will have another folder named after the model of your VuPlus set;
3.Copy the vuplus folder (including all the sub folders and files in it) to root folder of your USB stick;
4.WARNING!!! If you have any folder named vuplus on any device connected to your Vu+, delete the folder or rename it;
5.Turn off your Vu+;
6.Disconnect all USB flash drives connected to your receiver;
7.If your receiver is equipped with a front USB port (Duo2, Ultimo, etc.), insert the USB stick in it, otherwise you can insert the USB stick in a rear port.;
8.Turn on your Vu+.

If, for any reason, the upgrade fails, first disconnect any USB devices connected to your Vu+ and then try again to install the new image.
If the upgrade fails again, try to use another USB stick.



Vu+ Solo​

Update is done when green light blinks on the front panel.

[R3al.dx]

Mulțumesc @mondo !
Stiu etapele, am stb-ul in 2010 , ideea este că nu vrea sa instaleze nicio imagine Vti, superioară sau inferioară .
Am incercat cu 2 usb-uri, am descarcat mai multe imagini....nimic . Cand restartez stb-ul, licăre putin led-ul de la stick si nu se intamplă deca repornirea vechii imagini. Update de bootloader cred că are din 2011, am căutat unul mai nou dar nu am gasit .

[claudiu]

problema cu ledul rosu poate fi de la sursa ,de la placa de baza sau si sursa si placa de baza . La sursa in cele mai multe cazuri e vorba de condensatori umflati , la placa de baza cam aceeasi problema e vorba de condensatorii din jurul conectorului de alimentare din placa de baza . Daca sursa este functionala si condensatorii de pe placa de baza sint ok atunci e posibil sa fie procesorul -marusys nu prea a nimerit-o cu condensatorii cum nici problema racirii procesorului nu a gindit-o prea bine .

[bonou2]

intrebare de baraj :
Vu+Solo este original sau clona?

aici aveti o poza cu o sursa de tensiune a unui receptor ---Vu+Solo clona




defectul se manifesta in prima etapa led rosu se aprinde si atat
in a doua etapa led rosu dispare display este negru
cele trei condensatoare electrolitice mai mari trebuie inlocuiti

1500mf/10v inlocuit cu 1500mf/16v

succes

[roberto]

Salut!
Am o problema cu VU+ Solo SE V2, instalat openpli4, oscam, card local upc.
Cand schimb canalul atunci gaseste foarte greu cardul local, dureaza 5-10 secunde pana cand porneste canalul respectiv. Dupa pornire merge excelent, cu un timp de raspuns de aprox. 150ms, dar ma deranjeaza timpul de asteptare la schimb de canale. Ma poate ajute cineva cu niste sfaturi bune?

[danysev]

preferlocalcards = 2

Cand setati un oscam, aveti in dreapta o optiune si niste valori ... daca veti da click pe ea se deschide wiki cu explicatii