Oscam mai bun decat NEWCS !!!

[Diablo1]

@malin

Ia probeaza asta ?
TvrHD merge in newcs+mg
Oscam inlocuieste newcs deci pornesti oscam+mg si dai o linie N la CCcam ce zici ar merge ?

[laleauaneagra]

hai ca poate ma folosesc si eu de cardu de tvr intr un final

[zildan]

Magareala asta nu e noua, nu va bazati pe faza cu tras din cccam si pus cu 256 ca nu e stabil.
Ma temeam ca o sa devina publica si o sa avem belele.
Oscam deschide TVR HD si ca emu!
Asta e bine.

[zmeura]

Daca Oscam merge si ca emu nu doar citeste cardul atunci poate face update la card?Din ce vad din config nu sunt setari pentru asa ceva decat la partea de client.
Nu a spus nimeni cum functioneaza ca emu.Citeste chei?Primeste linii?Ce protocol suporta,doar newcamd?
Testati si sbox,poate va ajuta si cu update la carduri.
O sa-mi fac timp si pentru oscam daca voi ziceti ca merita.

PS: TVR nu merge pe cccam,indiferent cu ce este citit cardul.Cat timp incerci sa-l deschizi cu cccam e degeaba si bineinteles ca nici peersi nu vor avea imagine pe TVR de pe cardul din newcs,oscam,sbox,etc folosind cccam.

[zildan]

Exista versiuni compilate de oscam care deschid programele in local.
Trage din local, newcamd, cccam si alte linii pe care le potzi pune.
Daca tu ai TVR in CCcam pus local, eu cu oscam sau incubus deschid TVR din cardul tau.

[wambertos]

@zmeura
Exista posibilitatea de a seta AU in oscam.user.
Exista versiuni cu monitor, adica webif, care se poate accesa setind in oscam.conf portul http in felul urmator: httpport = 83 (sau un alt port liber).
De asemenea se poate parola accesul webif.
Am amintit de webif pt. ca se poate folosi la configurare.

[zmeura]

Deci face au de la user (sa zicem cccam) daca si acesta trimite emm-urile pentru cardul nostru.Inseamna ca legat de asta nu e diferenta fata de newcs,doar ca sa stim.

[dan2000]

face au de la user. la fel ca si newcs.

[malin]

In debug mod am observat ca trimite emm catre card, si primeste raspunsuri ok, de aici putem trage concluzia ca se poate face actualizare de card, din pacate nu am vazut concret un update ( inca nu a fost necesar ).
Exista intradevar si un monitor ( pe cel web nu am auzit nu am vazut ) insa cel din linia de comanda e acceptabil.

Am vazut in ultimele configuratie si legatura cu tunerul local, nu am probab daca e functional.


La buna vedere,
Malin

[zmeura]

Raspunsul cardului N3 in mbox:

 
Newcs    323-325 ms
Sbox      315 ms
Oscam    306 ms

In newcs cardul N3 "reuseste" inca reseturi la intervale aleatoriu.Sbox pare sa mearga bine dar crapa webif dupa o perioada si nu pot vedea situatia reseturilor,daca exista.Inca in oscam nu am vazut un webif si in altceva nu stiu cum sa-l urmaresc,are extrem de multe optiuni care cer mult timp pentru studiu.Nu inteleg de ce raspune greu la unele intervale de timp:

010/01/21 23:55:27 886 c01 mbox (1802&002011/055A/92:C964): found (270 ms) by digitv
2010/01/21 23:55:37 886 c01 mbox (1802&002011/055A/92:5F68): found (269 ms) by digitv
2010/01/21 23:55:48 886 c01 mbox (1802&002011/055A/92:C8C4): not found (1266 ms)
2010/01/21 23:55:51 886 c01 mbox (1802&002011/055A/92:C8C4): found (261 ms) by digitv
2010/01/21 23:55:57 886 c01 mbox (1802&002011/055A/92:EE4C): found (269 ms) by digitv
2010/01/21 23:56:07 886 c01 mbox (1802&002011/055A/92:AD0C): found (268 ms) by digitv
2010/01/21 23:56:17 886 c01 mbox (1802&002011/055A/92EAB): found (268 ms) by digitv
2010/01/21 23:56:27 886 c01 mbox (1802&002011/055A/92:6DD2): found (269 ms) by digitv
2010/01/21 23:56:37 886 c01 mbox (1802&002011/055A/92:910B): found (269 ms) by digitv
2010/01/21 23:56:47 886 c01 mbox (1802&002011/055A/92:B675): found (269 ms) by digitv
2010/01/21 23:56:58 886 c01 mbox (1802&002011/055A/92:088B): not found (1263 ms)
2010/01/21 23:57:01 886 c01 mbox (1802&002011/055A/92:088B): found (260 ms) by digitv
2010/01/21 23:57:07 886 c01 mbox (1802&002011/055A/92:6DF4): found (269 ms) by digitv
2010/01/21 23:57:17 886 c01 mbox (1802&002011/055A/92:EBA0): found (269 ms) by digitv
2010/01/21 23:57:27 886 c01 mbox (1802&002011/055A/92:FB18): found (268 ms) by digitv
2010/01/21 23:57:37 886 c01 mbox (1802&002011/055A/92:3FD2): found (270 ms) by digitv
2010/01/21 23:57:47 886 c01 mbox (1802&002011/055A/92:7A78): found (269 ms) by digitv
2010/01/21 23:57:57 886 c01 mbox (1802&002011/055A/92:4B1F): found (269 ms) by digitv
2010/01/21 23:58:07 886 c01 mbox (1802&002011/055A/92:E0BA): found (269 ms) by digitv
2010/01/21 23:58:17 886 c01 mbox (1802&002011/055A/92:90CC): found (270 ms) by digitv
2010/01/21 23:58:27 886 c01 mbox (1802&002011/055A/92:703B): found (268 ms) by digitv
2010/01/21 23:58:37 886 c01 mbox (1802&002011/055A/92:5B6B): found (268 ms) by digitv
2010/01/21 23:58:47 886 c01 mbox (1802&002011/055A/92:8074): found (268 ms) by digitv
2010/01/21 23:58:57 886 c01 mbox (1802&002011/055A/92:710A): found (268 ms) by digitv
2010/01/21 23:59:07 886 c01 mbox (1802&002011/055A/92:3830): found (269 ms) by digitv
2010/01/21 23:59:18 886 c01 mbox (1802&002011/055A/92:C63E): not found (1266 ms)
2010/01/21 23:59:21 886 c01 mbox (1802&002011/055A/92:C63E): found (281 ms) by digitv
2010/01/21 23:59:27 886 c01 mbox (1802&002011/055A/92:C614): found (268 ms) by digitv

De fapt zice "not found" cee ce cred ca inseamna ca nu raspunde cardul.
Se vede ca timpul de raspuns in oscam.log pare excelent (cand raspunde),dar in mbox este tot de peste 300ms.Punem la copt sa mai vedem.

[viking7691]

Salutare baieti am revenit sa anunt ca s-a rezolvat problema cu cardul de N3 Rom180 Ver Mer000 Caid 1880 functioneaza destul de bine nu destul de stabil dar este OK.
Multumesc binentelesc lui Malin pt ca el ma ajutat sa pun in functiune cele 2 emu cu cardul asta.
Totusi se pare ca este o diferenta mare intre cele 2 cartele de la DIDI N3 la Rom142 timpi de raspuns sunt mai mici pe cind la Rom180 de la 390ms pina la 420ms.
Cam atit sunt pt inceput primele impresii despre aceste carduri.


Salutari!h

[malin]

Aici vedem ca este acelaşi program, deci el există, altceva se intampla. Oscamul are ceva limitări la useri , cand un user işi depăşeşte norma ... ii trimite "fake" sau/şi un delay care este asemănător cu "not found" . Poate e asta.

2010/01/21 23:56:58 886 c01 mbox (1802&002011/055A/92:088B): not found (1263 ms)
2010/01/21 23:57:01 886 c01 mbox (1802&002011/055A/92:088B): found (260 ms) by digitv

Un fakedelay = 1000 ms la care punem media de 260 acces card ne da 1260 ..asta s-a intamplat la tine, user mobx a depasit limita si a fost prepenalizat.


In /var/tuxbox/config/oscam.conf

un exemplu care da drumul la carausi puternci cu trafic mare ...

[anticasc]

enabled = 1
numusers = 1
sampletime = 50
samples = 200
penalty = 1
clogfile = /tmp/oscam.penalty
fakedelay = 1000
denysamples = 180



The [anticasc] section (only if anti-cascading enabled)
enabled = 0|1
1 = enabled anti-cascading, default:0

numusers = quantity
anti-cascading: user per account, 0 = anti-cascading not permitted,
default:0

sampletime = minutes
duration of sample, default:2

samples = quantity
quantity of samples over limit, default:10

penalty = 0|1|2
level of penalty:

0 = only logging
1 = send fake CWs
2 = disbable user temporary

default:0, penalty can be overwritten per user in oscam.user

aclogfile = filename
file for anti-cascading logging, default:none

fakedelay = milli-seconds
fake delay time, default:1000

denysamples = quantity
How many samples should be penalized?, default:8



Aici sper ca o sa vin cu explicati mai detaliate, cred ca aici este si managementul corect al oscamului.

La buna vedere.

[malin]

cu acesta configurare

[anticasc]
enabled = 1
numusers = 1
sampletime = 1
samples = 60
penalty = 1
clogfile = /tmp/oscam.penalty
fakedelay = 1000
denysamples = 16

in log apare :

0:36:41 c06 osiris (1801&002011/0407/4A:1341): found (167 ms) by digitv
0:36:44 a user 'osiris' exceeds limit
0:36:48 c06 osiris (1801&002011/03F0/4A:7F87): fake (1121 ms)
0:36:50 c06 osiris (1801&002011/03EB/4A0DD): fake (1123 ms)
0:36:51 c06 osiris (1801&002011/0400/4A:33AF): fake (1121 ms)
0:36:52 c06 osiris (1801&002011/0407/4A:814F): fake (1121 ms)
0:36:58 c06 osiris (1801&002011/03F0/4A:F7E5): fake (1121 ms)
0:37:00 c06 osiris (1801&002011/03EB/4A:EE7D): fake (1121 ms)
0:37:01 c06 osiris (1801&002011/0400/4A:B567): fake (1121 ms)
0:37:02 c06 osiris (1801&002011/0407/4A:9A7B): fake (1121 ms)
0:37:08 c06 osiris (1801&002011/03F0/4A:9BCF): fake (1121 ms)
0:37:10 c06 osiris (1801&002011/03EB/4A:B328): fake (1121 ms)
0:37:11 c06 osiris (1801&002011/0400/4A:31D6): fake (1121 ms)
0:37:12 c06 osiris (1801&002011/0407/4A:C73C): fake (1121 ms)
0:37:18 c06 osiris (1801&002011/03F0/4A:85C3): fake (1121 ms)
0:37:20 c06 osiris (1801&002011/03EB/4A:01BB): fake (1120 ms)
0:37:21 c06 osiris (1801&002011/0400/4A:F4EB): fake (1121 ms)
0:37:22 c06 osiris (1801&002011/0407/4A:7C8A): fake (1121 ms)
0:37:28 c06 osiris (1801&002011/03F0/4A:3CD7): fake (1121 ms)
0:37:30 c06 osiris (1801&002011/03EB/4A:BDD7): fake (1121 ms)
0:37:31 c06 osiris (1801&002011/0400/4A:9BB0): fake (1121 ms)
0:37:32 c06 osiris (1801&002011/0407/4A:FDBA): fake (1121 ms)
0:37:38 c06 osiris (1801&002011/03F0/4A:7A6A): fake (1121 ms)
0:37:40 c06 osiris (1801&002011/03EB/4A:16E0): fake (1121 ms)
0:37:41 c06 osiris (1801&002011/0400/4A:C8B1): fake (1121 ms)
0:37:42 c06 osiris (1801&002011/0407/4A:64C0): fake (1121 ms)
0:37:44 a user 'osiris' restored access
0:37:47 c06 osiris (1801&002011/03F0/4A:E2E4): found (167 ms) by digitv

[Diablo1]

Oscam monitor is a very simple program to use.

1) Modify the OSCam configuration file as the follow
Code:
oscam.conf
# monitor
[monitor]
port = 988
aulow = 120
monlevel = 4
# modify this field with the address of your PCs
nocrypt = 127.0.0.1,192.168.0.151-192.168.0.152
Code:
oscam.user
[account]
#user = name
# account name, required
user = User
pwd = Password
2) In the "Server" field insert the IP of the OSCam machine.
3) The field "Port server" is the same of the configuration file
4) Port client is a fre UDP port (try with 1000)
5) User and Password is the reference of one user configured in "oscam.user" enabled to monitor.
6) "Start" and "Stop" enable to start and stop the log.
7) "Clean" is used to clean the old logged data.
8) If you want more detailed data to log, start oscam with -d63 parameter, but remember in this way, the ecm time is increased...

AICI Oscam Monitor 0,1 Full

Pentru E2 :oscam_0.99.4svn1298_mipsel_tuxbox_linux_monitor_improvement_entitlements.gz
AICI

Spor la teste !!!!

[wambertos]

Oscam webif(monitor) este integrat in multe versiuni:



@Diablo1
Asta e pt tine, pe fritzbox cu smargo si card TVR.

-------------------------------------------------------------------------------
>> OSCam <<  cardserver started at Fri Jan 22 21:55:59 2010
-------------------------------------------------------------------------------
2010/01/22 21:55:59   1803 s   version=0.99.4svn, build #1122, system=mips-dbox2-linux, nice=-1
2010/01/22 21:55:59   1803 s   max. clients=29, client max. idle=120 sec
2010/01/22 21:55:59   1803 s   max. logsize=unlimited
2010/01/22 21:55:59   1803 s   client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2010/01/22 21:55:59   1803 s   shared memory initialized (size=544764, fd=3)
2010/01/22 21:55:59   1803 s   auth size=4740
2010/01/22 21:55:59   1803 s   services reloaded: 0 services freed, 4 services loaded
2010/01/22 21:55:59   1803 s   userdb reloaded: 0 accounts freed, 1 accounts loaded, 0 expired
2010/01/22 21:55:59   1803 s   signal handling initialized (type=sysv)
2010/01/22 21:55:59   1803 s   2336 service-id's loaded
2010/01/22 21:55:59   1803 s   monitor: initialized (fd=7, port=988)
2010/01/22 21:55:59   1803 s   camd 3.3x: disabled
2010/01/22 21:55:59   1803 s   camd 3.5x: disabled
2010/01/22 21:55:59   1803 s   cs378x: disabled
2010/01/22 21:56:00   1803 s   newcamd: initialized (fd=8, port=20000, crypted)
2010/01/22 21:56:00   1803 s   CAID: 0500
2010/01/22 21:56:00   1803 s   provid #0: 025900
2010/01/22 21:56:00   1803 s   radegast: disabled
2010/01/22 21:56:00   1803 s   resolver thread started
2010/01/22 21:56:00   1803 s   logger started (pid=1806)
2010/01/22 21:56:00   1803 s   resolver started (pid=1807, delay=30 sec)
2010/01/22 21:56:00   1803 s   http started (pid=1808)
2010/01/22 21:56:00   1803 s   reader started (pid=1809, device=/dev/ttyUSB0, detect=cd, mhz=600, cardmhz=357)
2010/01/22 21:56:00   1803 s   Waiting for local card init ....
2010/01/22 21:56:00   1808 h   HTTP Server listening on port 83
2010/01/22 21:56:03   1803 s   Init for all local cards done !
2010/01/22 21:56:03   1803 s   anti cascading disabled
2010/01/22 21:56:54   1809 r03 card detected
2010/01/22 21:56:57   1809 r03 Warning: D=0 is invalid, forcing D=1
2010/01/22 21:56:57   1809 r03 ATR: 3F 77 18 00 00 C2 14 00 C1 68 90 00 
2010/01/22 21:56:58   1809 r03 type: viaccess(standard atr), caid: 0500, serial: 3211022495
2010/01/22 21:56:59   1809 r03 providers: 3 (FFF720,025900,025910)
2010/01/22 21:56:59   1809 r03 ready for requests
2010/01/22 21:56:59   1809 r03 card detected
2010/01/22 21:56:59   1809 r03 serial: 3211022495
2010/01/22 21:57:00   1809 r03 provider: 1, id: FFF720, name: TVR, sa: BF64509F, geo: empty
2010/01/22 21:57:00   1809 r03 provider: 2, id: 025900, name: TVR 1, sa: BF64509F, geo: FF FF FF FF 
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2010/01/01 - 2010/01/31
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/12/15 - 2010/08/26
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/12/05 - 2010/08/26
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/12/01 - 2009/12/31
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/10/05 - 2010/08/26
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/09/25 - 2010/08/26
2010/01/22 21:57:00   1809 r03 class: 0A, expiry date: 2009/07/01 - 2009/09/24
2010/01/22 21:57:01   1809 r03 class: 0A, expiry date: 2008/07/28 - 2009/02/27
2010/01/22 21:57:01   1809 r03 class: FF, expiry date: 2008/04/09 - 2008/05/08
2010/01/22 21:57:01   1809 r03 provider: 3, id: 025910, name: TVR 2, sa: BF64509F, geo: FF FF FF FF