Just two questions to those who have tested incubuscamd v0.82:
* Does it really work with CCcam 2.1.0 protocol
* Does Premiere HD work?
Thanks!
Printable View
Just two questions to those who have tested incubuscamd v0.82:
* Does it really work with CCcam 2.1.0 protocol
* Does Premiere HD work?
Thanks!
1. yes, it does work with cccam 2.1.0
2. Premiere HD works just fine :))
Pai mai oameni buni ...cu raspunsuri in doi peri ...cine poate sa inteleaga ceva ! Daca DA ...cum ! ce setari trebuie facute ... exemple ...si poate facem cu totii un pas inainte ! raspunsul in doi peri este mai rau decat tacerea !!!
Eu am incecat asa :
- SIF 031 flash
- incubus 082 sh40 enigma
- in incubusCamd.conf am facut urmatoarele declaratii
decoder_type=1
card_server_url_0=cccam://myuser:mypasswd@servername.homelinux.com:12000
... si din pacate nu decodeaza ... de ce ...uite asta ar fi un raspuns interesant !!!
[Prov:000000:CaID:0000]
decoder_type=1
card_server_url_0=cccam://myuser:mypasswd@servername.homelinux.com:12000
card_server_url_1=cccam://myuser22:mypasswd22@servername22.homelinux.com:12000
card_server_url_2=cccam://myuser333:mypasswd333@servername333.homelinux.com:12000
[Servers]
card_server_url=cccam://myuser:mypasswd@servername.homelinux.com:12000
card_server_url=cccam://myuser22:mypasswd22@servername22.homelinux.com:12000
card_server_url=cccam://myuser333:mypasswd333@servername333.homelinux.com:12000
[CaIDTunnel]
1833:1702:000000:0082 # this one should tunnel premiereHD nagra3 into betacrypt cards
1833:1702:000000:0081 # this one should tunnel premiereHD nagra3 into betacrypt cards
Oho ! un raspuns simplu, direct si usor ...ca un fulg de zapada ! raspuns care a imprastiat ceatza ! Tnks !
ok, eu am pus in incubusCamd.conf:
[Prov:000000:CaID:0000]
decoder_type=1
card_server_url_0=cccam://
[Servers]
card_server_url=cccam://user:pass@xxxxxxx.homelinux.com:12000
card_server_url=cccam://me22xxxxx:xxxxx@xxxxxxxx.homelinux.com:7369
atat. si am putut sa ma uit la Premiere HD. :)
asa a aparut prima configurare la 0.70 e corect si asa, dar se pare ca lucreaza mai bine cu cealalta varianta, mai ales la conectarea la mai multe servere. parerile sunt impartite.
20/06/2009, V0.85
- deleted old priority system for caid, now will be used firstly the prio and then a cycle selection
- SID in hex value instead of dec one
- fixed some bugs on caid ecm parsing
- fixes for stability/less-crashes (crashes were made by the pmt handling, using pmt file wich the writes is slower than the channel change,
now should be fixed in almost all cases)
- still open the 2.1.1 protocol support and previous version
- fixed a bug on reading keys for the internal emulator, now also unsupported softcam.key files are skipped in the unknown fields
(read the softcam.key file to see how to build a new one)
I think i need to explain something about last releases:
incubusCamd is born for cuberevo models, no other models are supported by my choiche.
I saw many tries to crack the cam... well, do as you like but do not associate stability problems to the cam, because stability
is tested only on cuberevo. Before open your mouth close your eyes and hope!
If you want to report any kind of bugs use usual international places, i will read them, but report only cuberevo bugs.
I don't mind about other boxes and on cuberevo for sure the connection shouldn't be lost after few minutes, this is caused by a low
level management of the protocol wich causes many bugs on all other boxes.
So to all people claiming about incubusCamd: I hope you could live 100 years to be able to ever see me enjoy.
[Only registered and activated users can see links. Click Here To Register...]
[Only registered and activated users can see links. Click Here To Register...]
21/06/2009, V0.86
- fixed one more bug for better stability and speed
- support for enigma 1 on cuberevo (use .sh4_e2 version)
[Only registered and activated users can see links. Click Here To Register...]
24/04/1915, V0.87
- fixed a bug on channel change stability
- fixed a bug on ecm cache
- support for caid 0603 on JSC sport channels
[Only registered and activated users can see links. Click Here To Register...]
V0.88
- fixed another bug on irdeto channels
[Only registered and activated users can see links. Click Here To Register...]
05/08/2009, V0.90
- fixed the bug for caid/provider selection for protocols
- optimized a little bit more the protocol selection (lot of improvements)
- added console server interface (you can log by telnet, check the config file: console_logs_broadcast, console_logs_broadcast_port)
- added more infos for current server and info like that, in file /tmp/ecm.info
[Only registered and activated users can see links. Click Here To Register...]
10/08/2009, V0.91
- fixed a bug on caid tunneling
- fixed a bug when a cw with same old value arrives
- added web interface (the config writer could have some bugs, it is not 100% tested)
- added log of ecm pid selected
- added timeout check on server connection (no more blocking if a fail server is given)
- fixed a check on multi-istances
- added on_screen_messages_ecm and on_screen_messages_emm (emm are disabled, so now is useless), pay attention,
it will pop-up a message on the screen each time an ecm decrypted successfully arrives
- if no more protocol or priority type will be selected (check_priority, cs_protocol_order) nothing will be used by default,
check the config file for more examples and infos
- added possibility to set priority/ignore on ecm pid (check the incubusCamd.prio file for more infos/examples)
- fixed a bug with emu given by cccam protocol servers
- fixed a bug on reading keys from SoftCam.Key file (also added possibility to use char ; or # for comments)
- now all emulators codifies should be ok, i can't test them all, so report if something is wrong (do not forget to use the SoftCam.Key edited
like the one attached in the release pack, because it's not like others softcam.key files)
- fixed a bug on reading config files, wich do not delete spaces ' ' when found
No EMMs are supported yet, so do not hope in that, emms will be implemented in a future version.
10/08/2009, V0.92
- solved once for all bugs with spaces and comments in config files
17-11-09, V0.95
- optimized service manager on e2 on FTA channels (no more cpu overload requesting PMT always)
- fixed a bug on dw log for internal emu showing wrong values
- added possibility to declare prov and caid set to 0000:000000 on newcamd server lines, this is usefull if you like to
use the server for many codifies or if you don't know exactly the values to put in (let's call it a jolly value)
- fixed CCcam 2.1.3 recognized like system
- fixed dw delay time written in file ecm.info
<A href="http://www.sendspace.com/file/526wtn" target=_blank>[Only registered and activated users can see links. Click Here To Register...]
Rog foarte mult sa ma ajutati, spun de ce. Sunt incepetor in sharring.De abia am facut rost de niste rinduri aprox 5-6,si asara cineva mi-a spart serveru oscam(lung de povestit),In afara de spart mai si pica ziua oscamu ,se opreste si gata.Ma dau afara clienti fiindca nu sunt online. M-am saturat ,asta e , si un alt motiv.
Am zis incerc cu asta daca stii ceva in legatura te rog sa-mi zici,e stabil sau nu?
Code:Am downloadat un incubuscamd 1.21 vesiune.Va pun file-ul .conf ,ma rog sa-mi semnati acolo cu o alta culoare unde trebuie modificat.Am portul 1200 deschis,as-i vrea ,si ,sa am webinerface. Cu oscam foloseam port 8888. As-i vrea sa dau la clientii mei cu hop 3 deci sa poate sa dea mai departe. Am un zip incubuscamd 1.21.tar.gz cum sa bag la locul lui? Cum pot instala? /menu/buton verde/emu/incubuscamd 0.99 si incubuscamd config 0.99
Downloadezi cum am facut cu oscam, si dupa file-uriile sa le schimb? Daca asa fac ,nu trebuie modificari in fisiere,ip-uri,porturi,enable disable /var/key , /var/bin ,/var/ emu? Am Pkt E2 ultimul 233 usb Ipbox 910 cu hdd. (daca stii spunemi si asta,la imaginnile astea E2 Pkt cum sa modifik user pasw pt ftp,pt telnetca si asara cineva a reusit sa intra in box,banuiesc stie paswordu pentru ca nu am schimbat a ramas originalul.)La Nlb stiu cum trebe din webinterface dar din pkt nu stiu cum se modifica. Va rog nu va suparati pe mine.Dar este important ca nu o sa mai am nici o linie.
Mersii pt rabdarea acordata.
Asta e vers 1.21 care am downlodat ultima data.
##############################################################################
# incubusCamd configuration file #
# All configuration options in this file observe the same format: #
# <configuration_name>=<configuration_value> #
# #
# Each section are [<section_name>:<option_1>:<option_x>] like. #
# #
# No matter about white spaces on any place or UNIX/DOS style files #
##############################################################################
########################### general configuration ############################
[General]
# Enable (1) or disable (0) background execution
# 0 - Off
# 1 - On
#
background_execution=0
# Set the nice value (priority) of the camd process
# possible values: -20 (most favorable scheduling) to 19 (least favorable).
#
nice_value=0
# This sets the level of console output for debugging:
# 0 - No debug messages, 1 - First level debug messages, 2 - Second level debug messages,
# 3 - Print all debug messages
#
debug_level=0
# This option enables (1) or disables (0) the writing of debug information to the
# console.
#
log_to_console=0
# This option enables (1) or disables (0) the writing of console output to a log file
#
log_to_file=0
# When log_to_file is set to 1, this is the path and filename to write console
# ouput to.
#
logfile_name=/var/bin/incubusCamd.log
# This is the path and filename to read SoftCam.Key file
# by default it will be searched in the /var/keys directory
#
softcamfile_name=/var/keys/SoftCam.Key
# This is the path and filename to read prio file
# by default it will be searched in the /var/bin directory, or in /etc, or in /var/keys
#
priofile_name=/var/bin/incubusCamd.prio
# This is the path and filename to read providersinfo file, used in webinterface
# by default it will be searched in the /var/bin directory
#
providerinfo_file_name=/var/bin/incubusCamd.providers
# This is the path and filename to read channelinfo file, used in webinterface
# by default it will be searched in the /var/bin directory
#
channelinfo_file_name=/var/bin/incubusCamd.channelinfo
# Used to activate on-screen messages. Username and password required if
# HTTP authentication is enabled on enigma.
# 0 - Off
# 1 - On
#
on_screen_messages_show=1
on_screen_messages_username=root
on_screen_messages_password=
on_screen_messages_key_update=0
on_screen_messages_wait_for_key_update=0
on_screen_messages_ecm=0
on_screen_messages_emm=0
# When activated, incubusCamd will listen on the specified port for connections. All
# log activity will be broadcast in real-time to connected clients.
#
console_logs_broadcast=0
console_logs_broadcast_port=666
# Enable/disable incubusCamd web interface (default port is 668).
# 0 - Disable
# 1 - Enable
#
webif=1
webif_port=668
# This is the port used to share your cards with other clients
# in other words this is the port where other clients must be connected to you if they want to
# receive your cards shared
# default is 12000
#
clients_port=12000
# This is the minimum client version required if you want to connect to the server
# with this setting you can force that clients at least use a certain version otherwise they are denied when logging in
# by default there is no minimum client version required
#
#minimum_clients_version=2.1.4
# Enable/disable a client on two hops away to send the updates to the cardserver
# 0 - Disable
# 1 - Enable
#
extra_emm_level=1
# Option to set global share limits
#
# global_limits={ caid:id(:downhops), caid:id(:downhops), ... }
#
#example:
#
#global_limits={ 0100:000080, 0622:000000:1, 0500:000000:2 }
#
# all users get no 0100:000080.
# and our 0622:000000 cards only for themself (1 hop down),
# and 0500 cards for themself plus one additional hop down.
# global limits are overridden by client specific limits (see [Clients] section)
########################### provider configuration ###########################
#
# All parameters are in hexadecimal notation.
# Each section is defined by the provider id value.
# If you don't know the provider id value then use the provider id "000000" and ca id "0000".
# On provider 000000 caid 0000 goes all provider wich are not declared. If the provider
# is declared then the cam will use the provider founded.
#
[Prov:000000:CaID:0000]
# ----------------------------------------------------------------------------
# this provider is a stand-in for all cards and all caid not declared previously
#
# You can select wich type of priority to assign on each caid/prov combination
# priority name available are: card,emu,cs
# card: internal card reader
# emu: internal emulator
# cs: card share protocols
# each type must be separated by a comma
#
# you can also set to use only cs and nothing more, to do it insert on each comma "cs"
# example: check_priority=cs,cs,cs # only cs in this case
# example: check_priority=card,emu,emu # no cs in this case
# obviously this is not suggested but if you prefer to disable an option you should do it in this way
# you can also declare only one type: check_priority=cs
# or two types: check_priority=cs,emu
# and so on
check_priority=cs,emu,card
# You can select wich protocol will be used first for the current caid/prov combination
# protocol name available are: newcamd,cccam,gbox,radegast,camd33,camd35,aroureos
# each protocol must be separated by a comma
#
# you can also declare only one type: cs_protocol_order=cccam
# or two types: cs_protocol_order=cccam,newcamd
# and so on
cs_protocol_order=cccam,newcamd,gbox,camd35,camd33,radegast,aroureos
# Enable (1) or disable (0) emm process when a cs protocol is used
# 0 - Off
# 1 - On
#
process_emms_on_cs_mode=0
# Enable (1) or disable (0) emm g type process
# 0 - Off
# 1 - On
#
process_emm_g=0
# Enable (1) or disable (0) emm s type process
# 0 - Off
# 1 - On
#
process_emm_s=0
# Enable (1) or disable (0) emm u type process
# 0 - Off
# 1 - On
#
process_emm_u=0
# Enable (1) or disable (0) seca 3 ecm pid handler
# when is set to On, it will try to use seca 3 ecm pid
# before try seca 2 ecm pid, otherwise seca 2 pid will
# be selected firstly
# 0 - Off
# 1 - On
#
seca3_handler=0
# This is the ChannelID wich will be used as first value
# on irdeto channels. Value "-1" means no preferred channel id will be used.
# You can use more than one pref chid, you have to separe them with a comma ',' (see example 2).
# The value is expressed as 4 digits hex value (2 bytes). Automatic change will be done.
# example: chid=0015
# example 2: chid=0015,002A
#chid=-1
# This is the max value wich will be used as comparing value
# for card's uphops. If a less or equal uphops will be found then the card will be used,
# the cards with greater uphops value will be ignored.
# The value is expressed as decimal value, by default a value equal to 5 is set by the cam
#max_check_uphops=5
#[Prov:000501:CaID:1833]
#check_priority=cs,emu,card
#cs_protocol_order=cccam,newcamd,gbox,camd35,camd33,radegast,aroureos
#process_emms_on_cs_mode=0
#process_emm_g=0
#process_emm_s=0
#process_emm_u=0
#seca3_handler=0
#chid=-1
#max_check_uphops=5
########################### servers configuration ############################
[Servers]
#
# This is the section for the multi-server configuration.
#
# URL of card-server to use, formats are as follows:
#
# newcamd://<username_31>:<password_31>@<hostname>:<port>:<caid_4>:<prov_id_6>/<des_key_14>/[EMM]/<nr_of_hops_away>
# aroureos://@<hostname>:<port>:<caid_4>:<prov_id_6>/[EMM]/<nr_of_hops_away>
# radegast://@<hostname>:<port>:<caid_4>:<prov_id_6>/[EMM]/<nr_of_hops_away>
# camd33://<username_10>:<password_10>@<hostname>:<port>:<caid_4>:<prov_id_6>/[aes_key_16]/[EMM]/<nr_of_hops_away>
# camd35://<username_32>:<password_32>@<hostname>:<port>:<caid_4>:<prov_id_6>/[EMM]/<nr_of_hops_away>
# gbox://<localhost>:<localport>:<password_8>@<peer_address>:<peer_port>:<peer_pass_8>/[EMM]
#
# cccam://<username_20>:<password_32>@<hostname>:<port>/[receive_emu_shared]/[EMM]
# where [receive_emu_shared] should assume value "yes" (without quotes, if you like to receive emus data shared by the server) or "no" (this is assumed by default)
# and it's an optional parameter.
#
# where [EMM] should assume value "EMM" (without quotes, if you like to send EMMs data to the server) or just do not add anything if you do not want EMM
#
# where <nr_of_hops_away> is the number of hopdown you want to share your card: by default is set to 1 (only one share down enabled from you)
#
# NOTE: The "EMM" suffix is optional and tells the card-server client whether
# to send EMM's to the card-server or not. Enabling or disabling this only
# has effect if the card-server is configured to accept emms from this client.
#
# NOTE 2: You can set value 0000 for caid and value 000000 for provider id on newcamd server if you want an all codifies working server
# or simply if you don't know wich value to set on, just put 0 value
#
# i.e:
#
#card_server_url=cccam://username:password@192.168.1.24:12000
#card_server_url=cccam://username:password@yourname.dyndns.org:15000
#card_server_url=gbox://yourname.dyndns.org:6666:password@hisname.dyndns.org:6666:peer_pass
#card_server_url=cccam://username:password@hostname:port/no # cccam without emu shared
#card_server_url=cccam://username:password@hostname:port/yes # cccam with emu shared
#card_server_url=cccam://username:password@hostname:port/yes/EMM # cccam with emu shared and with EMM enabled
#card_server_url=gbox://192.168.1.24:5555:password@192.168.1.32:4444:peer_pass
#card_server_url=newcamd://username:password@192.168.0.100:10550:0500:028800/0102030405060708091011121314
#card_server_url=radegast://@192.168.0.100:10550:0100:000065
#card_server_url=aroureos://@yourhostname.dyndns.org:10666:0500:007C00
#card_server_url=camd35://username:password@192.168.0.50:14150:0603:000000
#card_server_url=camd33://username:password@192.168.0.50:10550:0603:000000 # cam33 without AES encryption
#card_server_url=camd33://username:password@192.168.0.50:10500:0604:000000/01020304050607080910111213141516 # cam33 with AES encryption
#card_server_url=newcamd://username:password@192.168.0.100:10550:0500:028800/0102030405060708091011121314/EMM/2 # EMM is enabled for this server and will share this card 2 hops away from us
#card_server_url=newcamd://username:password@192.168.0.100:10551:0000:000000/0102030405060708091011121314/EMM/0 # this server will be used with all codifies because of value 0 for caid and provid, no share for this card
########################### clients configuration ############################
[Clients]
#
# This is the section for the multi-client configuration.
# The port used to make other clients connected is declared in the general section like "clients_port".
#
# URL of card-client to use, formats are as follows:
#
# cccam://<username_20>:<password_32>@[hostname]/[allow_emu_shared]/[receive_EMM]/[uphops] { caid:id(:downhops), caid:id(:downhops), ... } { caid:id:sid, caid:id:sid, ... } { begintime-endtime, ... }
# where [hostname] should assume value of your client ip address if you want to make limitation on address connections for an account
# where [allow_emu_shared] should assume value "yes" (without quotes, if you like to share emus data with clients, this is assumed by default) or "no"
# where [receive_EMM] should assume value "yes" (without quotes, if you like to receive EMM data from clients, this is assumed by default) or "no"
# where [uphops] is the max number of uphops of cards that can be shared to the client
# downshare limits per share (default = no limits) and optional
# downshare limits per share based on caid:id:sid
# and optional timeslots in which share is valid (to block channels on box of children after 19:00 for instance)
# if no timeslot is defined 24 hrs a day is used
# emus are shared only one level down, even if no limits given
#
# i.e:
#
#card_client_url=cccam://username:password@192.168.1.15/yes/yes # this clients will receive emu and can send emm to us
#card_client_url=cccam://username:password@192.168.1.21/no # this client can not receive emu but can send emm to us
#card_client_url=cccam://username:password@192.168.1.20/no/no # this client can not receiver emu and can't send emm to us
#card_client_url=cccam://username:password@192.168.1.23/no/yes # this client can not receive emu but can send emm to us
#card_client_url=cccam://username:password@192.168.1.222/yes/no # this client can receive emu but can't send emm to us
#card_client_url=cccam://username:password@yourname.dyndns.org # this client will receive emu and can send emm to us
#card_client_url=cccam://username:password@ # this client will receive emu and can send emm to us and has no restriction on the hostname address, previous examples have all restriction on one address
#card_client_url=cccam://username:password@/yes/no # this client will receive emu but can't send emm to us and has no restriction on the hostname address
#card_client_url=cccam://username:password@/no/no/2 # this client can't receive emu and can't send emm to us and has no restriction on the hostname address and gets all our shares at max 2 hops from us
#card_client_url=cccam://username:password@/no/no/2 { 0100:000080, 0622:000000:1, 0500:000000:2 }
# this client can't receive emu and can't send emm to us and has no restriction on the hostname address and gets all our shares at max 2 hops from us
# gets no 0100:000080 and our 0622:000000 cards only for himself (1 hop down),
# and 0500 cards for himself plus one additional hop down.
#card_client_url=cccam://username:password@/no/no/2 { 0:0:3, 0100:000080:1 }
# this client can't receive emu and can't send emm to us and has no restriction on the hostname address and gets all our shares at max 2 hops from us
# get's to share them down two further levels beyond his own level.
# But he is not allowed to share 0100:000080 down to other users.
#card_client_url=cccam://username:password@/no/no/2 { 0:0:3, 0100:000080:1 } { 0100:000080:15df }
# this client can't receive emu and can't send emm to us and has no restriction on the hostname address and gets all our shares at max 2 hops from us
# get's to share them down two further levels beyond his own level.
# But he is not allowed to share 0100:000080 down to other users.
# He is also not allowed to view channel 0100:000080:15df
#card_client_url=cccam://username:password@/no/no/2 { } { } { 12:00-17:00, 19:00-20:00 }
# this client can't receive emu and can't send emm to us and has no restriction on the hostname address and gets all our shares at max 2 hops from us
# the share is only valid between 12:00 and 17:00 and between 19:00 and 20:00
# outside these hours the share will not give cw's to the client
########################### CaIDs tunneling configuration ############################
[CaIDTunnel]
#
# All values are in hex notation
# In this file you can configure what CAIDs/PIDs incubusCamd should tunnel to another CAID
#
# situation 1: this caid, all idents, on all channels will use the tunnel_caid
# caid:tunnel_caid
#
# situation 2: this caid/ident pair will use the tunnel_caid
# caid:tunnel_caid:ident
#
# situation 3: this caid/ident pair, on channel 'sid' will use the tunnel_caid
# caid:tunnel_caid:ident:sid
#
# i.e:
#
#1833:1702:000000:0082 # this one should tunnel premiereHD nagra3 into betacrypt cards
#1833:1702:000000:0081 # this one should tunnel premiereHD nagra3 into betacrypt cards