Printable View
Pentru ghinionistii carora nu le porneste Incubuscam-ul pe configuratia data de Zildan Ii roga sa incerce asta.
Cu ea am reusit sa fac si eu lumina.
[Prov:FF00]
card_server_url_0=cccam://<user>:<pass>@<hostname>:<port>
[Servers]
card_server_url_1=cccam://<user>:<pass>@<hostname>:<port>
a reusit sa porneasca cineva incubusCamd_0_75 pe kathrein? ..... ca la mine nu vrea.
Porneste inainte de e2 sau in standby, din key dar nu deschide.
Cred ca ceva nu e legat bine in vers de e2.
Hello,
does anyone get Incubus higher than 0.55 running on the kathi?
I tried 0.70 0.75 and 0.80
nothing will run.
only 0.55 runs and that very bad. have to restart it every few minutes because it freezes.
Perhaps someone can help me to get a newer version running.
Thanks
Regards
Alex
No version after 0.55 will run on kathy. You should try mbox, it's a lot more stable and most important, works on kathy.
Ar putea cineva sa-mi explice daca s-a lovit de urmatoarea problema:
Am instalat incubus 0.55, am pus fisierele de .conf si .prio la locul lor, am adaugat linia de cccam de doua ori, asa cum scrie la tutorial. Insa, emu-ul nu porneste nici mort, se opreste imediat, fara vreun mesaj de eroare sau ceva. Vreo sugestie?
Mai verifica linia din server, vorbeste cu cel care ti-a dat-o.
in conf file pune inainte de linia cu [PROV....] asta:Quote:
Originally Posted by liviurosio [Only registered and activated users can see links. Click Here To Register...]
decoder_type=1
Apoi:
[Prov:FF00]
card_server_url_0=cccam://***********
Apoi:
[Servers]
card_server_url_0=cccam://***********
Da restart la box.
Vezi daca merge.
what's the config for 3 servers CCcam ?
[Prov:FF00]I tested this, without succes :dance:
card_server_url_0=cccam://***********
card_server_url_1=cccam://***********
card_server_url_2=cccam://***********
[Servers]
card_server_url_0=cccam://***********
card_server_url_1=cccam://***********
card_server_url_2=cccam://***********
Thanks a lot in advance
hello for all
i have kati ufs 910 white 2 enigma image on usb flash barry allen (aaf_sussex_revolutions_ba_image) & (AAFmod_E2-BA_Weihnachtsimage_TDT_rev600.tar.gz) but the incubusCamd not started
on kati or any image how any can help me pleas whatiis a prablem?
tanks
on 0.55 you can use only one line so the config will be:Quote:
Originally Posted by dreanew [Only registered and activated users can see links. Click Here To Register...]
[Prov:FF00]
card_server_url_0=cccam://***********
[Servers]
card_server_url_0=cccam://***********
on last 0.80 you can use more line but the config shoul be:
[Prov:FF00]
card_server_url_0=cccam://***********
card_server_url_1=cccam://***********
card_server_url_2=cccam://***********
[Servers]
card_server_url=cccam://***********
card_server_url=cccam://***********
card_server_url=cccam://***********
more ex:
[Prov:000000:CaID:0000]
decoder_type=1
card_server_url_0=cccam://user1:pas1@host1.no-ip.biz:12000 #12000=peer port
card_server_url_1=cccam://user2:pas2@host2.no-ip.org:12000
[Servers]
card_server_url=cccam://user1:pas1@host1.no-ip.biz:12000
card_server_url=cccam://user2:pas2@host2.no-ip.org:12000
Thanks a lot for your reply,
but I did not know use the 0.80 version on the kathrein with enigma² RSP firmware. :dance:
Could You please give a link for download new Incubus 0.80 what works on Kathrein UFS 910 enigma2 ?
[Only registered and activated users can see links. Click Here To Register...]
home/emu/incubus
Thank You for fast reply!Quote:
Originally Posted by Snow [Only registered and activated users can see links. Click Here To Register...]
Can You please confirm that it works on Kathy UFS 910 e2 (for RSP latest e2 image?) ?
I have just understood that 0.55 is latest working Incubus for Kathy UFS 910 , and the team has finished Kathy support???