Probleme rescriere imagine Spark

Printable View

Show 20 post(s) from this thread on one page

01-01-12, 18:18
daradici

Daca ai nevoie de cablul nullmodem, eu dupa [Only registered and activated users can see links. Click Here To Register...]a folosesc, facut din cablu UTP.

Se gasesc in comert cabluri de 3m, aproape la orice magazin de tehnica de calcul.
Eu a trebuit sa-l construiesc din cauza lungimii neconventianal de mari (aprox 25M !!!).
01-01-12, 20:53
proteus

Iaca am gasit la un prieten un cablu verificat, si-a refacut un DM800 cu el. Surpriza, este fix aceeasi cablare ca si la cablul pe care il am deja. Am fost sambata pe la cateva magazine de calculatoare pe aici, nu mai tine nimeni cabluri seriale. Nici pe net sa comand nu prea gasesc.

Oricum, am 2 cabluri care au mers sigur cu Kathy si respectiv DM800. Doar la Alien nu merg. Logic, eu cred ca buba e la Alien totusi.

Dar o sa mai caut nenorocitul asta de cablu serial, desi la momentul asta asa imi vine sa-l trimit inapoi in garantie, ca batem pasul pe log degeaba.

Si multumiri din inima celui care s-a gandit ca un "factory reset" nu este util.

---------- Post added at 18:53 ---------- Previous post was at 17:24 ----------

Am taiat unul din cablurile pe care le am si am facut cablul recomandat de Zildan (2-3, 3-2, 5-5). Nu merge deloc, in Putty nu vad nimic venind pe seriala.

------------------

OK, si daca totusi nu cablul e problema, ce alte optiuni mai sunt? Ce s-ar mai putea face?
01-01-12, 20:57
MaximusFBI

Eu zic sa il lasi vreo 24 de ore scos din priza si fara cablu satelit si dupa sa incerci cu spark rescue cu stick-ul.
01-01-12, 21:30
proteus

OK, cu ce anume difera daca e scos din priza 5 sau 24 de ore? Exista vreo explicatie fizica/logica?

Dupa cum am spus mai sus, cablul satelit a fost scos deja. Iar stick-ul i-l bag degea, daca nu ajunge la emergency boot.
01-01-12, 21:39
MaximusFBI

Nu stiu explicatia dar am patit cu un opticum la fel ramasese blocat cand upgradam un sw .
L-am lasat o zii si dupa a mers fara probleme .
La probleme anormale solutii anormale.:)
01-01-12, 22:02
stargate

Code:

U-Boot 1.3.1 (Mar 16 2011 - 11:42:45) - stm23_0043 - YW 1.0.019 Rel P1 DRAM: 128 MiB NOR: 8 MiB NAND: 512 MiB In: serial Out: serial Err: serial IdentID : 09 00 0a 00 00 4b b0 Hit ESC to stop autoboot: 0 Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000 ** Bad Magic Number 0xffffffff ** ## Booting image at 80000000 ... Bad Magic Number ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...

O eroare de genul celei de mai sus am primit atunci cand am instalat prima data imaginea lui @pinky care este format YAFFS2 si nu cum sunt celelalte imagini sunt JFFS2 fapt ce duce la o schimbare de bootargs . Eroarea s-a rezolvat la acel moment cu ajutorul lui @zildan , apoi am invatat cum se face o instalare in format YAFFS2 si apoi trecerea din nou la JFFS2 fara sa am erori . Ciudat este ca Spark mergea rescris fara probleme ... problema era la Enigma . Problema la tine este imposibilitatea de a iesi manual din autoboot fie cand incerci pornirea cu butonul OK apasat fie pe seriala ... si daca cablul serial este ok atunci a intervenit o problema grava si uboot nu mai comunica cu panoul frontal si nici pe seriala .
02-01-12, 00:38
proteus

Quote:

Originally Posted by MaximusFBI [Only registered and activated users can see links. Click Here To Register...]

La probleme anormale solutii anormale.:)

Maestre, m-ai salvat! Paranormal, nu alta. Am fost plecat cateva ore, l-am scos din priza si am scos toate cablurile din el. Can m-am intors, a mers din prima sa intru in Emergency boot.

Acum pare totul OK, am instalat ultimul Enigma RSP si acum il configurez.

E de antologie toata faza....
02-01-12, 11:27
stargate

Bine ca ai rezolvat ... probabil nu il lasai deloc dupa ce il opreai din intrerupatorul din spate , in general este bine sa fie lasat 1-2 minute pentru a se descarca complet toti condesatorii din aparat .

Spor la teste
02-01-12, 14:06
proteus

OK, e de retinut pentru viitor. Multumiri inca o data pentru efort.
29-07-13, 23:04
iannys

Probleme rescriere imagine Spark

Buna seara la toata lumea.Aceeasi problema o intimpin si eu ca si Proteus dar ca la mine nu vrea sa-si revina singur nici in ruptul capului ramine tot la load.Am tot incercat cu diferite marci de stickuri si cu cisco tftp si nu vrea deloc.Ce ma sfatuiti sa m-ai incerc?As incerca si cu hyper terminal cu u-boot.bin dar nu-l gasesc.Daca ati putea posta un link de unde sa-l descarc as incerca.
30-07-13, 15:56
gauloises

Trimite-l la garantie.
Aaa am patit si eu si nicicum nu l-am putut resuscita

Sent from my GT-I9100 using Tapatalk 4 Beta
30-07-13, 23:23
zildan

Daca ai cablu serial vezi mai concret care e buba.
Aparatul poate fi resuscitat!
30-07-13, 23:27
iannys

Probleme rescriere imagine Spark

Da am cablu cu care rescriu imaginea la dreambox.Sper ca este ok. Da-mi niste sfaturi ideii detalii despre cu as putea sa-l readuc la viata pe extraterestru
31-07-13, 00:14
zildan

Conectezi cablu serial, setezi seriala cu putty 115200 8 N 1 apoi vezi pe terminal meniul.
31-07-13, 22:13
iannys

Probleme rescriere imagine Spark

Timed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCC
Ce anume ar trebui sa vad ?
Doar asta imi arata putty.
01-08-13, 22:52
zildan

Clar nu !
Porneste seriala inainte de a da power on.
01-08-13, 23:21
iannys

Probleme rescriere imagine Spark

2˛ b°
c 6łm-đ
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCC
Asta arata acum.
02-08-13, 10:33
zildan

Ca sa recapitulam .... daca pornesti tinand apasat OK se schimba ceva in logul asta?
03-08-13, 00:48
iannys

Probleme rescriere imagine Spark

Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **
** Unable to use usb 0:1 for fatload **
Warning: MAC addresses don't match:
HW MAC address: FF:FF:FF:FF:FF:FF
"ethaddr" value: 00:80:E1:12:06:38
Using MAC Address 00:80:E1:12:06:38
*** ERROR: `ethaddr' not set
Asta arata daca tin butonul ok apasat.

---------- Post added at 23:48 ---------- Previous post was at 23:34 ----------

<ŰŤľ[ý˙
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CC
Asa arata cind incerc sa-l pornesc pe spark

ŰDŰ}żíý
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCC
Asta arata cind incerc pe enigma 2
03-08-13, 00:59
iannys

Probleme rescriere imagine Spark

Ďýë˝˙
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCC

Asta arata cind incerc pe spark

ß˝ý÷
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD

U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 0a 00 00 1d 4c
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.28_stm24_0207
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2209787 Bytes = 2.1 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCC

Asta pe enigma 2

Show 20 post(s) from this thread on one page