Oscam - emu

Salutare cine ma poate ajuta cu un oscam emu.ipk cel mai nou pentru Blackhole?
poate cineva daca vrea sa trimita unul pentru mine in pm va rog .

@[Only registered and activated users can see links. Click Here To Register...]
de ce nu copiezi oscam_ul ptr ca de la v3.0.1 nu mai funktioneaza ipk pe BH

Oscam 11209 preconfigurat, pentru BlackHole 3.0.x

- card tvr/freesat viaccess
- card tvr/freesat conax
- card focussat
- AU
-pornirea softcamului se face din blue panel (tasta albastra)
-weibif user admin /password admin port 8888
- acesare se face pe adresa [Only registered and activated users can see links. Click Here To Register...] si se va activata cartela posedata de dumneavoastra


Oscam mipsel [Only registered and activated users can see links. Click Here To Register...]
Ocam-emu (nu contine Softcam.key) mipsel [Only registered and activated users can see links. Click Here To Register...]
Oscam armv7 (Vu SOLO 4k) [Only registered and activated users can see links. Click Here To Register...]

multumesc foarte mult :)

---------- Post added at 08:16 ---------- Previous post was at 08:12 ----------

sombra am incercat meroda de copiere dar nu face nimic nu deschide nimic am dat chmd 755 si tot cum tebuie dar nimic de aia am cerut ipk ca cu ipk instalat functioneaza

Stii sa pornesti manual oscamul din telnet?

nu prea ce trebuie facut ?
ca pina acum am instalat un ipk si ala functiona normal dar acum nimic alea vechi daca pun asa functioneza gen oscam 11102 emu de ex .

---------- Post added at 10:10 ---------- Previous post was at 10:06 ----------

inca o intrebare daca am acum pus in box oscam 11102 emu si suprascriu cu oscam 11211 emu si reglez tot atunci trebuie pornit din telnet ??

Daca ai un ipk functional, poti schimba doar executabilul oscam pastrand doar numele celui original.
La atribute pui 755 !
Dupa ce le schimbi dai un emu stop apoi emu start din meniuri (panel etc), nu e necesar telnet pentru asta.

asa am facut si nu merge de aia intreb cum si ce dupa ce fac toate astea nu deschide nimic si nu situ und e problema ??

Depinde cum are oscamu preconfigurata (la compilare) calea filei de setari.
Poate fi in /var/keys la unu din ele si in alta parte la celalalt.
Oricum asta se poate verifica din telnet.

@[Only registered and activated users can see links. Click Here To Register...]
Poftim [Only registered and activated users can see links. Click Here To Register...] bagale asa cum sint in box la tine Atribute 755 , box new start ....

S-a reluat munca la OSEMU:


October 2017 update (revised)

As of October 2017 the BISS code has been greatly improved.

The old code distinguished channels only by using the service id (sid) and any one of the ecm pid (which for 99.99% of the channels is the same) or the channel's video and audio pids. As a result there were too many key clashes in the SoftCam.Key file. These formal (legacy) methods of channel identification remain in the new code as well for backwards compatibility and for those users that have a small number of keys in their SoftCam.Key and don't experience collisions. This way no editing is needed for the SoftCam.Key to work with the revised BISS code.

The revised code makes key searches based on crc32 hashes. There are two different hashes available:
The namespace hash, which is calculated by the enigma2 namespace (orbital position, frequency, polarization) and the service id of the channel. These two alone are enough to create a unique channel identifier.
There's also a universal hash, which is calculated using every pid of the channel (service id, pmt, video and audio pids). This universal hash, while not being unique as the namespace hash, is available on every box (enigma and non-enigma) and is a better alternative than oscam's constant cw protocol, since it takes audio pids into account, as well.
Using hashes to match keys, we get a distinct (unique in the case of namespace hash) identifier for each channel, which makes OSCam-Emu ideal for descrambling not only a huge amount of regular channels, but also for occasional transmitions (feeds).

Va rog un oscam emu pentru raspberry pi3,si cum pot sa-l pun, ce comenzi trebuiesc.
Multumesc.

@xrm
[Only registered and activated users can see links. Click Here To Register...] ai unul compilat la zi cu tot ce-ti trebuie.
folderul de config e in /usr/local/etc/
extragi arhiva, il redenumesti in oscam, si il pui in /usr/bin/
Din consola , sub root, executi
chmod 755 /usr/bin/oscam
apt update && apt upgrade
apt install libusb-1.0 libssl-dev libpcsclite1 libpcsclite-dev nano
[Only registered and activated users can see links. Click Here To Register...] gasesti informatii despre cum sa-ti creezi un script systemd.

De configurat ... fiecare are propriul lui server si la fiecare e altfel ... citeste [Only registered and activated users can see links. Click Here To Register...]

Ok, multumesc.
Mai am o intrebare:
cum sterg vechiul oscam(normal) de pe raspberry pi3,ca sa-l adaug pe acesta?

Il cauti unde este executabilul, il redenumesti la fel si il pui peste.
Locatia probabila este in /usr/bin/ sau in /usr/local/bin/

Cel mai usor cauti in service /etc/init.d/oscam (asta daca ai sysvinit)

Salutare, utimele versiuni de oscam nu au CacheEX, din cate am citit trebuie compilat oscam-ul lucru la care nu ma pricep, poate compila cineva o versiune si sa o puna pe site.

Multumesc !

depinde de cine a compilat aceea versiune, posibil sa fie o versiune lite. am rugamintea sa specifici si arhitectura pentru care doresti oscam-ul.

are integrate prajiturile sau are nevoie de softcam.key?
eu am pus separat osemu + reader in oscam din el....

Salut... si Hristos a Inviat! de o saptamana ,ma lovesc de o problema. Am un Octgon sf8008 cu o imagine Openatv 6.2 .Si OSCam r11517-795.
Scriu linia cccam [in oscam] readers, o salvez, se salveaza, dar nu se conecteaza, nu deschide....un ajutor va rog. Mentionez ca sunt novice in oscam. Dar promit ca o sa-mi pierd toata vara cu el. Multumesc pentru orice sfat!Chiar si in pm. va rog!

Foloseşte interfaţa web a Oscamului, şi va fi mai uşor.