Smargo Smartreader tutorial
This tutorial assumes the user has a DM7020 or a DM800. The tutorial can be used as it is, or adapted easily for a standard Linux setup.
How to set smartreader operating mode using Windows (It did not work for it in Vista for me, It worked in XP)
1: Install the windows drivers found here [Only registered and activated users can see links. Click Here To Register...]
2: Open smartreader.exe
3: Plug the smartreader into a usb port
4: Select Autoswitch or fixed mode
5: Select Normal or Dreambox kernel
6: Make sure it returns with "writing settings successful"
7: Done
DM7020 dreambox installation with PLI Iolite/Jade
1: Telnet to your dreambox run "ipkg update"
2: Run "ipkg install kernel-module-ftdi-sio"
3: Exit
4: Rename your original bootup file in /etc/init.d/ incase you have a problem*
5: Replace the bootup file in /etc/init.d/ with this one [Only registered and activated users can see links. Click Here To Register...]. The bootup file is in the zipfile.
6: Reboot
7: Plug in the smartreader
8: Insert your card. Make sure the chip on the card faces the same direction as the lights on the reader.
9: Done
* The latest PLi Jade Final image appears to already have the usbtoserial configured in the bootup file. So no need to replace the bootup file.
DM800 dreambox installation with PLI Iolite/Jade
1: Enter the download menu
2: Search for USBtoSerial drivers
3: Download
4: Reboot
5: Plug in the smartreader
6: Insert your card. Make sure the chip on the card faces the same direction as the lights on the reader.
7: Done
DM7020/cccam.cfg
CCcam configuration sample:
SERIAL READER : /dev/usb/tts/0 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6860002
SERVER LISTEN PORT : 20000
WEBINFO LISTEN PORT : 21000
WEBINFO USERNAME : username
WEBINFO PASSWORD : password
SHOW TIMING : yes
It is possible to add a usb hub to the DM7020. To incorporate a 4 port hub into the config insert the following:
SERIAL READER : /dev/usb/tts/0 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6860002
SERIAL READER : /dev/usb/tts/1 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/1 6860002
SERIAL READER : /dev/usb/tts/2 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/2 6860002
SERIAL READER : /dev/usb/tts/3 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/3 6860002
DM800/cccam.cfg
CCcam configuration sample:
SERIAL READER : /dev/ttyUSB0 smartreader+
SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 6860002
SERVER LISTEN PORT : 20000
WEBINFO LISTEN PORT : 21000
WEBINFO USERNAME : username
WEBINFO PASSWORD : password
SHOW TIMING : yes
The DM800 comes with 2 USB ports already. However if you wish to add a usb hub you can.
The above cfg's assume that the reader is set to autoswitch mode and dreambox kernel.
You can choose any of the following frequencies: 3.20, 3.43, 3.69, 4.00, 4.36, 4.80, 5.34, 6.00, 6.86, 8.00, 9.61, 12.0 and 16.0
Examples:
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6000002 runs the card at 6mhz.
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6860002 runs the card at 6.86mhz.
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 8000002 runs the card at 8mhz.
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 9610002 runs the card at 9.61mhz.
Most cards run at 6000002 or 6860002.
For latest PLI image released on 31st Jan 09, please add the below lines to your CCcam.cfg file. The configuration in the above post will only work with pli-enigma2 jade dm800 31st Oct 08.
SERIAL READER : /dev/usb/tts/0 smartreader+
or
SERIAL READER : /dev/usb/tts/1 smartreader+
Re: Smargo Smartreader tutorial
This Post is copied from here [Only registered and activated users can see links. Click Here To Register...]
I dont mind but atleast should have said 'THANKS' to the poster.
Re: Smargo Smartreader tutorial
The links above for the drivers are dead. Here are the new one
Click Below
[Only registered and activated users can see links. Click Here To Register...]
Click Below
[Only registered and activated users can see links. Click Here To Register...]
Enjoy!
Re: Smargo Smartreader tutorial
Tutorial for Smargo Smartreader for linux PC
''
Here is little help how to setup smartreader+ successfully under linux PC.
1: Linux PC setup.
Make sure that your installed linux distro wich has kernel 2.6.12 or newer version!
2: Update your smartreader+ if it has v1.2 or older firmware with v1.3 Link to download: [Only registered and activated users can see links. Click Here To Register...]
3: Before update make sure your reader is 100% reconized by linux!
You will find inside that "smartreader_v103.zip" very precise how to update that device.
Now disconnect smartreader+ disable from CCcam smartreader+ config lines and make restart to linux PC.
If linux is UP plug smartreader to USB and wait little so 20 second. Log to server and type command: dmesg
you should have like this:
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB
Serial Device
ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: Detected FT232BM
usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
usbcore: registered new driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
So your smartreader+ is ready to update the firmware.
4: Uptate beginning.
Copy to your PC linux server FTP 2 files:
srp_tools_x86
srp_update_x86
Set on console to both file chmod 755 !
Chek if your smartreader+ needs to update.
Run command: ./srp_update_x86
and you see like so:
smartreader+ version v1.0, v1.1 or v1.2 then you have time to update.
5: Upadte.
I DO NOT RESPONSIBLE IF SOMETHING GOES WRONG WITH FLASH!
Run command: ./srp_update_x86 -b
smartreader+ version v1.1
bootloader mode activated
Remove and reinsert SmartReader+ then restart application
Then new command: ./srp_update_x86 -f
start flashing
------------------------------------- done
Please remove and reinsert SmartReader+
remove the reader and reinsert now we start the config tool
Run command: ./srp_tools_x86
smartreader+ version v1.3
MODE autoswitch
FREQ 3.69 Mhz
KERNEL normal
T_MODE t = 0
EGT 0
successfully flashed the reader with new firmware.
Now we need add to CCcam.cfg new line:
SERIAL READER : /dev/ttyUSB0 smartreader+
SERIAL READER : /dev/ttyUSB1 smartreader+
SERIAL READER : /dev/ttyUSB2 smartreader+
or whatever USB port your smartreader is entered.
Save CCcam.cfg and run ./CCcam.x86 -d you should see new card is added and running.
In CCcam.cfg is card overklocking and there you just edit like so:
SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 4800000 and card works with 4.80mhz set by smartreader+.
Available frequencies
3.20, 3.43, 3.69, 4.00, 4.36, 4.80, 5.34, 6.00, 6.86, 8.00, 9.61, 12.0 and 16.0 MHz
The user can selected any frequency. The Smartreader+ will selected the nearest available.
Default sartreader+ speed is with new v1.3 firmware 3.69MHZ and most cards works with that speed.
And more configuratsion optins you will find inside smartreader_v103.zip. ''
[Only registered and activated users can see links. Click Here To Register...]
Re: Smargo Smartreader tutorial
smargo serial avec tuto pour dream 800HD ( in french )
'' voici le logiciel smargo serial avec tuto pour dream 800HD
installer dans
/lib/modules/2.6.12-5.1-brcmstb-dm800/kernel/drivers/usb/serial
ftdi_sio.ko
pl2303.ko
usbserial.ko
editer le fichier bootup metre ceci a la fin
echo 90 > /proc/progress
modprobe ftdi_sio
dans menu parametre kernel
le fichier usb ftdi_sio.ko ( metre oui )
n oublié pas de configuré le smargo sur pc
[Only registered and activated users can see links. Click Here To Register...]
Pour Gemini2 4.10
Dreambox 800/7025/8000
- BluePanel
- Paramètres
- Modules Kernel
- USB Cardreader (Chipset FTDI): oui
Smargo via le soft smartreader_v103
- Mode: Autoswitch
- Kernel: Dreambox
- T-mode: T=0
- EGT: 0
fichier ccam.cfg
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/0 6800000
SERIAL READER : /dev/usb/tts/0 smartreader+ 00
SMARTCARD CLOCK FREQUENCY: /dev/usb/tts/1 6800000
SERIAL READER : /dev/usb/tts/1 smartreader+ 00 ''
download :
[Only registered and activated users can see links. Click Here To Register...]
smargo cu newcs sau oscam in DM800 (OE1.6)
Sunt solutii de accesare smargo smartreader+ cu newcs sau oscam?; DM800 cu enigma2 GP versiune 5.x (OE 1.6) ?
Am smargo firmware 1.4 si vreau sa-l folosesc numai cu newcs sau oscam. Pe CCcam merge.
Ar fi nevoie de un newcs sau oscam compilat cu suport pentru smartreader+.
Ma descurca cineva? sau nu se poate?
Am mai incercat cu newcs.mips.usb care este ptr. infinity. N-a mers.
asa ca ... I need you. Help me :cheers:
