Linie N

Salut, va rog daca imi poate spune si mie cineva cum pot adauga o linie N . Mentionez ca am card local digi , folosesc sbox+cccam pe un dm500 cu gemini 4.6 .

Va Multumesc

Ii dai pur si simplu copy/paste de la cel care ti-a dat-o. Ea trebuie bagata in cccam.cfg care il gasesti in /var/etc.

Scuze

Da, greseala mea ca nu m-am exprimat bine . Vreau sa dau la cineva o linie N si nu am idee cum . Multumesc mult pentru raspuns.

Cauti fisierul user.sbox la dm500 parca e in /var/keys (depinde ce imagine ai), si linia care o gasesti in el cu userul tau (linia din cccam.cfg al tau) o dublezi,
apoi pui alt user si pass in ea, deschizi portul de newcamd care il gasesti in sbox.conf in ruter si linia care o dai va fi la fel ca a ta din cccam.cfg dar cu alt user si pass
Citeste in user.sbox

Code:

#Example configuration file for sbox cardclient server #Add newcamd user #NC=dummy dummy slot0 #NC=dummy dummy slot0 0 #NC=dummy dummy slot0 0 150 #NC=dummy dummy slot0 0 150 ip # | | | | | | |__________ user ip (optional) # | | | | | |_____________ user timeout in sec min. 150 max. 1440 (optional) # | | | | |________________ 0=au disabled for this user 1=au enabled for this user (optional) # | | | |____________________ server to which this user belongs # | | |__________________________ password for this user # | |_______________________________ username # |____________________________________ newcamd client #NC=edk edk slot0 1 #NC=edk2 edk2 slot1 0 #Add radegast server #RS=ip port caid provider # | | | | |__________________ provider # | | | |________________________ caid # | | |______________________________ server port # | |__________________________________ server ip # |____________________________________ radegast server #RS=127.0.0.1 16050 1800 000000 #Add newcamd server #NS=ip port user pass deskey au # | | | | | | |________ enable send emms, 0=send all 1=dont send emm-s 2=dont send emm-u 4=dont send emm-g # | | | | | |______________ deskey # | | | | |____________________ password # | | | |_________________________ user # | | |______________________________ server port # | |__________________________________ server ip # |____________________________________ newcamd server #NS=127.0.0.1 15050 dummy dummy 0102030405060708091011121314 7 #Add cccam server #CS=ip port user pass 3 # | | | | | |________________ max hops (min.1 max.6) # | | | | |____________________ password # | | | |_________________________ user # | | |______________________________ server port # | |__________________________________ server ip # |____________________________________ cccam server #CS=127.0.0.1 15050 dummy dummy 3 #Add cccam client #CC=user pass #CC=user pass 5 0 1 #CC=user pass 5 0 1 { 0:0:1 } #CC=user pass 5 0 1 { 0:0:1 } userip # | | | | | | | | | |______ user ip (optional) # | | | | | | | | |____________ max down hops (optional) # | | | | | | | |______________ without use (optional) # | | | | | | |________________ without use (optional) # | | | | | |____________________ 0=au disabled for this user 1=au enabled for this user (optional) # | | | | |______________________ without use (optional) # | | | |________________________ gets all our shares at max 5 hops from us (optional) # | | |___________________________ password # | |________________________________ user # |____________________________________ cccam client #CC=dummy dummy 3 0 0 { 0:0:1 } 192.168.0.154

si in sbox.conf

Code:

[main] server_only=0 # 0=mixed mode 1=only server log=0 # 1=no log 1=log to /tmp/sbox.log //ALWAYS USE 0// logudp=192.26.0.1:3354 # server ip:server port userspath=/var/bin/users.sbox # users list channelinfo=/var/bin/sbox.channelinfo # channel info webinterface=1 # 1=web interface on 0=web interface off webadmin=admin:edk # user:pass for webinterface webport=8181 # web interface port rdgserver=0 # 0=radegast server off 1=radegast server on rdgport=16050 # radegast server port use_nagra=0 # 1=use as nagra card 0=use as irdeto card (only for nagra over irdeto cards) prio=1800:0000;0100:1111:2222 # prio caid for dvbapi, caid1:prov1;caid2:prov2:prov1 cccam=0:18000 # 0=cccam server off - 1=cccam server on : cccam server port betatunnel=1 # 0=betatunnel support disabled 1=betatunnel support enabled [slot0] active=1 # 0=inactive 1=active sci=/dev/sci0 # lower ncdserver=0 # 0=newcamd server off 1=newcamd server on deskey=0102030405060708091011121314 # newcamd deskey port=15050 # newcamd port mhz=500 # Mhz for card in this reader, DON'T WORK ON PHOENIX INTERFACE. Example: mhz=357, mhz=368 reader=1 # 0=phoenix, 1=sci (internal reader), 2=smartreader cache=0 # how many ecms can be cached, 0 or less=cache disabled # How to ADD RSA for TIGER/NCMED cards # If your card is a ROM TIGER547 Rev124 (for example) # [TIGER547] <- this is the rom version from your card # rsa=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx # ONLY THIS, for config bloquer, portlist, etc, look at the examples above! #Nagra2/3 Example [CCCCCCCC] # nagra2 camid (4 bytes) rsa= # rsa "n" from this card (like newcs) boxkey= # boxkey from this card emm=0 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath=/var/keys/port.list # path from port.list #Nagra tiger/ncmed Example [CCCCCCCC] # nagra camid (4 bytes) emm=2 # 0=accept all 1=block emms 2=block emmu 4=block emmg portlist=0 # use portlist or no portlistpath= # path from port.list

Limitare linie N

Salutari tuturor,am urmaoarea intrebare: detin un openbox s9 si un dm 800 clona,din openbox s9 cu un card focus ( active familia) am dat o linie n in DM,fiind local am ecm foarte bun si deschide ob02 din linia N,dar din pacate deschide doar ce e in familia,la restul imi arata ce deschide din N dar e ecranul negru,pot sa limitez cumva sa deschida de la N familia si restul de la altii?

sid assign sau oscam.services...habar nu am ce emu folosesti:)

si nu se limiteaza N ca nu prea ai cum.....treaba o faci acolo unde ai cardu

N

pai cardul e in openbox,de acolo dau linia N,asta parca are emu un fel de cccam,si nu cred ca se poate face ceva la el,ma gandeam ca pot modifica in DM