Deblocare telecomanda?

Am primit revista info satelit in care scria despre folosirea telecomenzii vu si la televizor. Am introdus codurile cum scria in revista, dar surpriza, nu imi mai merge volumul de pe telecomanda. Daca apas butoanele V+ si V- de pe receptor atunci functioneaza. Am pus alta imagine crezand ca problema e din receptor. Dar problema nu era de la receptor ci din telecomanda. Am dat sa revin la setarile din fabrica atat la TV cat si la receiver. Dar degeaba. Toate butoanele functioneaza cu exceptia volumului. Ce sa fac? Sa cumpar alta telecomanda?

incearca cu multi quickbutton

Nu vad optiunea de volum in multi ouickbutton.

da tu codurile unde le-ai bagat la reciver, sau in tv , cred ca in tv , nu vad cum poate asta influenta reciveru , schimba bateriile scoatele de tot ...
poti sa dai un link cu articolul despre care vb?

Aici scrie ce este si in revista info-sateliti ultimul numar...am bagat codurile laa telecomanda de la vu+uno ca sa nu mai folosesc si pe cea televizorului.
Mai jos redau de pe acel forum ce spune si in revista info-satelit:
"Un alt lucru care mi-a atras atentia a fost telecomanda. Aparent identica cu cea de la modelul Duo si Solo, aduce o mica inovatie. Telecomanda poate fi programata pentru a o folosi si pentru televizorul d-vs, nemaifiind nevoie sa aveti ambele telecomenzi.
Botonul de mute a fost transformat in buton de on/off pentru tv. Programarea se face apasand concomitant butoanele 1 si 3 pana cand se va aprinde ledul. Introduceti codul de 4 cifre al televizorului pe care il puteti gasi in manul, iar daca televizorul raspunde comenzilor primate, fixate codul apasand tasta Ok + Stop. Daca nu gastiti condul in manual, introduceti dupa ce-ati apasat tasta 1 si 3, codul 0000. Pe urma apasati in mod repetat butonul power din stanga telecomenzii pana televizorul va raspunde la comanda. Procedeul dureaza, dar poate fi util in cazul in care nu gasiti in manual codul televizorului".



[Only registered and activated users can see links. Click Here To Register...]

Hmm, foarte curios ce spui. Eu n-am intalnit problema asta. Ce varianta ai incercat? Ai bagat direct codul tv-ului sau cu 0000.

Am incercat prima data 0000 si apoi codurile de la samsung (caci eu am televizor samsung )

Ok si cand apesi pe volume televizorul raspunde la volume?

later edit. Pentru ca dupa ce o programezi iti merge volumul doar la tv. Poti schimba sa treci pe stb. Ei recomanda sa-ti fixezi volumul pe vu la maxim sau jumate, iar de urma sa te folosesti de sonorul tv-ului.

---------- Post added at 01:02 ---------- Previous post was at 00:57 ----------

4. Mode Switch of Volume + / - and Mute
For the sake of easy volume control, please set the STB volume at 50% of the maximum level and set
this level as the default volume level from STB. Then, you just have to control your TV volume only without
having to adjust STB volume at the same time.
Set-up Sequence: <<1 + 6>>, <9>, <9>, <3>, <TV Power or STB Power>

1. Press 1and 6 for three seconds until LED is on.
2. Press <9>, <9>, <3>.
3. If you want to control of TV volume, press TV Power button. If you want to control STB volume, press
STB Power button.

---------- Post added at 01:03 ---------- Previous post was at 01:02 ----------

Iar daca vrei sa resetezi telecomanda asa cum a fost

5. Reset of TV Set-up
In case you want to reset the configured TV set-up of your RCU,
Press Sequence: <<1 + 6>>, <9>, <9>, <6>
1. Press 1and 6 for three seconds until LED is on.
2. Press <9>, <9>, <6>.
3. This will reverse the RCU into no configuration state.

---------- Post added at 01:09 ---------- Previous post was at 01:03 ----------

Nu trebuie sa schimbi telecomanda, trebuie doar sa citesti manualul.:drinks:

Hai sa te ajut:

Quote:

---

1. TV setting
Set-up Sequence: <<1 + 3>>, <4digit brand-code>, <<Mute or Power>>
1. Press number 1and 3 for three seconds until LED is on.
2. Find your TV brand-code from the TV code list and insert 4 digit code.
- If you press “0000”, Full Automatic Scan will start. This will take a while.
3. Keep pressing Mute button (or Power) until your TV is muted (or turned off)
4. If your TV is muted (or turned off), stop pressing Mute button.
5. Now, your RCU is in test mode and press Volume + /- to check if your TV responds.
6. If the volume buttons are operational, Press <OK + STOP ( )> to escape from the set-up mode.
2. AV setting
AV button is for the selection of TV video source. AV button may be automatically set up depending on TV
models. In case it is not automatically configured, please follow the instructions below.
Set-up Sequence <<1 + 9>>, <<AV>>
1. Press 1 and 9 for three seconds until LED is turned on.
2. Keep pressing AV button until your TV responds and displays the video input source.
3. If AV button is working, check if AV button is properly working several times.
4. Press <OK + STOP ( )> to escape from the set-up mode.
3. RCU Buttons for TV
* Buttons for TV only: TV Power. AV
* Buttons switchable between TV and STB: Volume +/ - and Mute
- These buttons are for STB only before the RCU set-up is done.
- It is switchable only after the configuration is done.
* All the other buttons are for STB only
4. Mode Switch of Volume + / - and Mute
For the sake of easy volume control, please set the STB volume at 50% of the maximum level and set
this level as the default volume level from STB. Then, you just have to control your TV volume only without
having to adjust STB volume at the same time.
Set-up Sequence: <<1 + 6>>, <9>, <9>, <3>, <TV Power or STB Power>

1. Press 1and 6 for three seconds until LED is on.
2. Press <9>, <9>, <3>.
3. If you want to control of TV volume, press TV Power button. If you want to control STB volume, press
STB Power button.
5. Reset of TV Set-up
In case you want to reset the configured TV set-up of your RCU,
Press Sequence: <<1 + 6>>, <9>, <9>, <6>
1. Press 1and 6 for three seconds until LED is on.
2. Press <9>, <9>, <6>.
3. This will reverse the RCU into no configuration state.
6. System Code Change.
You can change the system code of your Vu+ universal RCU according to the Vu+ model that you want to
control. The default system code is Mode 2.
Mode 1 : SOLO / DUO
Mode 2 : UNO
Mode 3 & 4 : reserved for future models.
Press <<2 + 7>>, <HELP>, <0001 or 0002 or 0003 or 0004>
1. Press 2 and 7 for three seconds until LED is on.
2. Press HELP
3. Press <0001 or 0002 or 0003 or 0004>

---

Ura ....asta era,esti un mare [Only registered and activated users can see links. Click Here To Register...] iarasi,mii de multumiri.

Cu placere :) Nu e mare lucru, rezolvai si singur cu putina atentie.