Probleme noi pentru mine, poate ma ajutati.
Dupa furtunile din ultimele saptamini, la o cadere de tensiune, s-a dus toata configurarea mea. Mai precis interfata phoenix nu mai raspunde la comenzi si a fost prima banuiala ca nu functioneaza corect, mai ales ca alimentatorul a cedat. Mbox merge, dar newcs nu.
Am luat legatura cu gelvis si am inlocuit interfata.
Am reinstalat imaginile atit in flash (9580) cit si in usb (AAF si 0.5.0).
Am repus ultima salvare (care mergea) la fisierele de configurare atit la flash cit si in usb pentru mbox 6.10 cu newcs 1.62.
Din pacate nu am mai reusit sa fac sistemul sa mearga. Mbox in continuare merge in share dar nu se conecteaza la newcs.
Am suspectat cartela (Max), dar in cam via merge si si-a luat subscriptia normal.
Folosind MCC la tab newcs cind o vede cind nu, iar userii nu sunt conectati.
Mesajele sunt:
la mbox
[21:13:55] [NEWCAMD] Trying to connect to newcamd server (127.0.0.1:10110)
[21:13:55] [NEWCAMD] Connected to (127.0.0.1:10110) ...
[21:13:55] [NEWCAMD] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).
[21:13:55] [NEWCAMD] Login request was rejected (127.0.0.1:10110).
newcs
[ 20:01:02 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 20:01:02 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 20:01:04 ] [ Phoenix ] Setting Parity to: ODD
[ 20:01:04 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB0
[ 20:01:04 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:01:05 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB0
[ 20:01:07 ] [ Loader ] Reset failed ...
[ 20:01:07 ] [ Loader ] Starting Newcamd Server on port 10110
Am mai incercat folosind informatiile de pe forum sa pun o cartela tvr, cu modificarile corespunzatoare in cwshare si port list, dar nu a mers.
Mai mult, folosind cartela de tvr am incercat sa o citesc direct in mbox dar am primit un mesaj hilat cum ca cartela este nagra:
[18:56:03] [/dev/ttyUSB0] Reseting device...
[18:56:03] [/dev/ttyUSB0] Reading ATR ...
[18:56:05] SHORT ATR
[18:56:05] [/dev/ttyUSB0] Found Nagravision smart card ...
[18:56:05] [/dev/ttyUSB0] smartcard: unknown (status: 00 00)
[18:56:05] [via]Init card failed !!!
cwshare
C: { 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 05004F00:05024F00 }
newcs
<?xml version="1.0"?>
<!--
For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)
-->
<newCSconfig>
<globals>
<listening-ip>127.0.0.1</listening-ip>
</globals>
<readers name="Card Readers">
<device>
<name>Phoenix Interface</name>
<type>phoenix</type>
<mhz>357</mhz>
<node>/dev/ttyUSB0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
<device>
<name>upper</name>
<type>Sci</type>
<node>/dev/sci1</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10010</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
</readers>
<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>
<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>
<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile>/tmp/newcs.txt</logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
</user>
</newcamdserver>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>
<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>
<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>
Unde gresesc?
Multumesc pe aceasta cale celor care nu m-au sters inca din lista.