PDA

View Full Version : HD900 USB-RS232 Card reader extern Pheonix



otheitis
18-09-08, 01:33
Problema care are ipbox 900HD e ca nu are card reader intern.Pt asta problema a iesit o solutia.Cine e interesant trebuie sa citeste pe pdf mai jos.E in limba italiana.

HD900USB-RS232.pdf (http://www.upload-drive.com/2044/HD900USB-RS232_pdf)

Aica e si mgcamd-1_30d_newcs-1_62usb-rs232

mgcamd-1.30d_newcs-1.62usb-rs232phoenix.tar.gz (http://www.upload-drive.com/2045/mgcamd-1_30d_newcs-1_62usb-rs232phoenix_tar_gz)

Aica e si drivers pt 900 si 9000.Cine are sifteam 0.1.6 poate sa il face download direct prin sifteam panel..
usb_serial-900&9000.rar (http://www.upload-drive.com/2116/usb_serial-900_9000_rar)

Snow
18-09-08, 02:06
Folosesc asta de saptamana trecuta, am incercat pe serial dar n-am reusit. Pe usb a mers simplu mai ales dupa ce-am modificat putin un newcs.xml trimis de wambertos. Alta e insa problema, inca nu face reshare, dar stiu ca nu mai e mult pana se va putea si lucrul acesta

otheitis
18-09-08, 12:27
Eu cred ca toate lucruri merge foarte bine la toate domenii cu ipbox 900 si 9000.Ieri am avut iar pe confirmatia ca lucreaza pt enigma.Dar nu am luat raspuns cind o sa fie gata.

pacala68
18-09-08, 12:48
mai bine cresteau pretul cu 20Eur la 900 si ii puneau un CR la nastere .
mai bine se cauta pe mainboard daca are conector pentru CardReader .
mai bine se incerca NewCS compilat pentru infinityUSB .

otheitis
18-09-08, 13:54
Modelul abcom 910HD o sa are slot intern.Care o sa apare in curind,si o sa fie exact ca 900HD.

motoru
24-09-08, 18:35
Am incercat in viteza phoenix programmer, pana acum am ajuns la urm. concluzii:
-pe portul serial nu funcioneaza.
-sanse ar fi prin intermediul conv. USB to RS232(adaptor usb to serial).

Am montat interfata prin portul USB nu reusesc sa vad cardul. Poate fi problema de driver sau configurare newcs. Nu am reusit sa aprofundez suficient problema am avut doar 10 minute la dispozitie.
Cine a testat configuratia si cunoaste problema rog o mana de ajutor.

otheitis
24-09-08, 19:30
Vorbeste cu snow el are 900 si a incercat sa face cu phoenix si a reusit.Roaga pe el sa te spune tot procedura.Undeva la config eu cred ca gresesti....Ai incercat pe plugin pt torrente?

motoru
24-09-08, 22:07
Asta e newcs la mine.
Are cineva habar ce nu bate ???


<?xml version="1.0"?>
<!--

For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)

-->



<newCSconfig>

<readers name="Card Readers">
<device>
<name>lower</name>
<type>Sci</type>
<node>/dev/sci0</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>

<device>
<name>upper</name>
<type>Sci</type>
<node>/dev/sci1</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10010</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
</readers>

<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>

<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>

<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
</user>


</newcamdserver>

</newCSconfig>

motoru
24-09-08, 22:13
sa bunghit forumul, uite unde mia pus postul !

Acum e ora 21:11 si la ultimul post al otheitis de acu cateva ore zice ca-i 22 si ceva !!!

Bai da nika nu mai merge http://www.sateliti.org/images/smilies/Comp_arunc.gif

Snow
24-09-08, 22:36
merge fara batai de cap cu mgcamd pe imaginea celor de la sif. instalezi cu ajutorul tastei rosii, in addon panel gasesti acolo mgcamd+newcs+pheonix

pentru mbox exista doar mbox+newcs
aici e de lucrat la configurari, cum voi avea ceva functionabil voi posta

nu uita sa dai jos si pluginul pentru usb to serial

nu merge pheonix pe interfata seriala a receptorului, doar usb

motoru
24-09-08, 22:56
merge fara batai de cap cu mgcamd pe imaginea celor de la sif. instalezi cu ajutorul tastei rosii, in addon panel gasesti acolo mgcamd+newcs+pheonix

pentru mbox exista doar mbox+newcs
aici e de lucrat la configurari, cum voi avea ceva functionabil voi posta

nu uita sa dai jos si pluginul pentru usb to serial

nu merge pheonix pe interfata seriala a receptorului, doar usb


Multumesc mult snow !

Problema e ca sunt indragostit acum de mbox, mai exat imi place mbox control center fff mult si asa ceva nu am gasit pt mgcamd(poate exista).
Prefer sa mai incerc sa setez newcs in combinatia cu mbox.
Daca mai ai ceva informatii in directia asta ar fi super.

otheitis
24-09-08, 23:30
mbox control are si limba romana hehehehe!!!!poate apare si pc editor cu limba romana ceva mischarile fac si acolo!!

Snow
25-09-08, 00:12
Ok, am unit discutia cu cea postat otheitis mai devreme pentru ca in mod normal aici ar fi trebuit sa continue discutia.
cand este un post deschis nu mai deschideti altele, va rog
folosit search

Snow
25-09-08, 23:27
Configurarea a fost facuta pe ipbox 900, imaginea sifteam 0.1.7, adaptor usb/serial (cumparat de la daniel 10x) si o interfata pheonix (home made - gasiti la gelvis sau la elstar)
Dupa ce ati instalat imaginea si ati facut setarile de baza ( limba, ora, scanare) cu ajutorul tastei rosii intrati in SIF-TEAM Panel, alegeti Install si cautati driverul pentru usb/serial. Il instalati dupa care iesiti si cu ajutorul RCC sau a unui ftp manager instalati scriptul pentru mbox de aici http://www.sateliti.org/showpost.php?p=49103&postcount=25 in var/bin
Urmati practic pasii din directionare, doar ca in loc de cam_mboxll_all, alegeti cam_mboxll_newcs_1_62_wo_cfg_files
Dupa ce ati intstalat softcamul, intrati in key, aveti grija ca in mbox.cfg sa aveti linia D {2 } Dati save si iesiti.
Pe urma in var/tuxbox/config fisierul newcs.xml trebuie sa fie setat in felul urmator:


<?xml version="1.0"?>
<!--

For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)

-->



<newCSconfig>
<globals>
<listening-ip>127.0.0.1</listening-ip>
</globals>
<readers name="Card Readers">
<device>
<name>Phoenix Interface</name>
<type>phoenix</type>
<mhz>357</mhz>
<node>/dev/ttyUSB0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>

<device>
<name>upper</name>
<type>Sci</type>
<node>/dev/sci1</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10010</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>
</readers>

<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>

<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>

<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
</user>


</newcamdserver>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>

<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>

<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>










Am sa-l si atasez. Dupa ce ati editat si fisierul acesta porniti mbox-ul din tasta verde.
Ca sa fiti siguri ca driverul pentru adaptorul usb a pornit apasati tasta rosie, pe urma galbena (script) si cautati scrplg-usb_serial_900hd_START.sh Apasati ok



Cam asta e
In cwshare puneti si linia
C: { 127.0.0.1 15000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 }
sau

C: { 127.0.0.1 15000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0100006a:0100006B;} { 1420:A200:B302:}


Specialistii in newcs va pot da mai multe lamuriri care e mai buna

Snow
27-09-08, 16:31
Rectificare, nu scoateti "#" din fata liniei #C: { 127.0.0.1 7999 } Am observat ca nenoroceste serverele de gbox la care sunteti conectat. Inca in teste.
Folositi newcs.xml asa cum este si puneti linia C in cwshare.cfg

Snow
02-10-08, 02:44
Antentie configurarea este doar pentru ipbox 900!!!!
Cu multumiri lui Zildan pentru ajutorul oferit.


<?xml version="1.0"?>
<!--

For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around :o)

-->



<newCSconfig>
<globals>
<listening-ip>127.0.0.1</listening-ip>
</globals>
<readers name="Card Readers">
<device>
<name>Phoenix Interface</name>
<type>phoenix</type>
<mhz>357</mhz>
<node>/dev/ttyUSB0</node>
<parity>even</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10110</newcamd_port>
<priority>round</priority>
<sid>
<allow>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</allow>
<deny>
<!-- valid value for id are:
4 numbers, if the service id is 3 numbers, add a 0 infront of it. -->
<id></id>
</deny>
</sid>
</device>

</readers>

<radegastserver>
<!-- valid value for enable are:
0,1 - Enable or Disable radegast server. -->
<enabled>no</enabled>

<!-- valid value for port are:
0,65535 - Which port to listen for incomming connections. -->
<port>10001</port>

<!-- valid value for allow are:
ALL - Not active yet. -->
<allow>
<hostname>127.0.0.1</hostname>
</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>verbose</level>
<type>init</type>
<output>all</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>bla</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<allow>lower</allow> <!--Use this just when you want give free just some readers to your Users -->
<allow>upper</allow> <!--Use this just when you want give free just some readers to your Users -->
</user>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
</user>


</newcamdserver>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>

<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>

<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
</newCSconfig>





in cazul meu portul pentru newcs este 10110 linia C e de genul

C: { 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0B000000:0B000000;}

unde { 0B000000:0B000000;} este id-ul cardului meu

1200.list se redenumeste in 10110 list si se scrie linia SF: { 0000 } desi cel mai bine e sa scrieti sid-ul la fiecare canal in parte in aceasta lista

va atasez mai jos si fisierul newcs.xml

tic2000
02-10-08, 11:05
1200.list se redenumeste in 10110 list si se scrie linia SF: { 0000 } desi cel mai bine e sa scrieti sid-ul la fiecare canal in parte in aceasta lista



Daca ai pachetul complet poti sa pui linistit 0000, daca insa nu il ai trebuie sa pui sid-urile canalelor pe care card-ul tau le poate deschide.

livs
02-10-08, 20:32
Cum verific daca ipbox comunica cu interfata Phoenix?

Snow
02-10-08, 22:42
cu gbox control center ultima versiune, sau dai pe canalul care stii ca ar trebui sa-l deschida carul tau si apesi tasta galbena
daca scrie local, trage de pe ea, daca scrie network atunci....

otheitis
02-10-08, 22:46
Sau cu telnet
te conectezi si scrii
cd var / keys
si dupa scrii
mbox.sh40
si vezi daca decodeze local sau network si de unde....

livs
11-10-08, 17:55
Am pus phoenix cu mgcamd+newcs+rs232 si a mers (card TVR).

Am trecut la mbox+newcs+rs232 si nu merge sa citesc local cardul.

La debug imi apare:

*************** New Start 11.10.2008 19:49:19 ***************

[19:49:19] STAPI INIT ... OK :)
[19:49:19] ExYuSAT Team http://www.exyusat.com , http://mbox.exyusat.com/index.php
[19:49:19] Starting MBOX version 0.4 BETA (build 0012) coded by The_Ripper
[19:49:19] This program is for educational & informational purposes only!!
[19:49:19] Donation to project: http://mbox.exyusat.com/donate.htm
[19:49:19] ===> Local Mode <===
[19:49:19] Reading cwshare.cfg ...
[19:49:19] Trying to get online,please wait ...
[19:49:19] Total 1 newcamd server(s) to connect
[19:49:19] Creating ecm parser thread ...OK
[19:49:19] Creating timer thread ...OK
[19:49:19] Creating newcamd worker thread ...OK
[19:49:19]
[19:49:19] ReReading pmt.tmp
[19:49:19] ==================================================================
[19:49:19] ECM: CA ID: 0x1702 Nagravision -> CA PID: 0x1009
[19:49:19] ECM: CA ID: 0x1722 Nagravision -> CA PID: 0x1009
[19:49:19] ECM: CA ID: 0x1830 Nagravision -> CA PID: 0x1948
[19:49:19] ECM: CA ID: 0x1833 Nagravision -> CA PID: 0x1848
[19:49:19] ECM: CA ID: 0x1834 Nagravision -> CA PID: 0x1C48
[19:49:19] ECM: CA ID: 0x09C4 NDS -> CA PID: 0x1B48
[19:49:19] ECM: CA ID: 0x1801 Nagravision -> CA PID: 0x1648
[19:49:19]


La restart a plecat pe premiere.


==================================================================
[19:49:19] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[19:49:19] [newcamd] Connected to (127.0.0.1:10110) ...
[19:49:19] [newcamd] Got card with CaID 0x0500 and 3 number(s) of ProvID (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0xFFF720 (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0x025900 (127.0.0.1:10110)
[19:49:19] [newcamd] Card: CaID 0x0500 ProvID: 0x025910 (127.0.0.1:10110)
[19:49:19] [newcamd] Creating newcamd worker thread for (127.0.0.1:10110) ...
OK
[19:49:38]
[19:49:38] ReReading pmt.tmp
[19:49:43]
[19:49:43] ReReading pmt.tmp
[19:49:43] ==================================================================
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0032
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0033
[19:49:43] *ECM: CA ID: 0x0500 Viaccess (00000000) -> CA PID: 0x0034
[19:49:43] ==================================================================
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:49:43] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:49:43] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:49:51] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:49:51] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:01] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:01] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:11] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:11] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:21] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:21] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0032...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0032, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0033...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0033, sidpid:0x0002 cant decode localy
[19:50:31] Searching CW cache for CaID 0x0502, pid 0x0034...no CW in cache
[19:50:31] Dropping local ECM , caid:0x0502, ecmpid:0x0034, sidpid:0x0002 cant decode localy


Ce se intimpla, nu am imagine?

pacala68
12-10-08, 01:29
lipsa mgcamd ( alte emu parca nu pot lucra corect cu ecm TVR )

rocco2007r
07-11-08, 22:38
Salut,

Tot eu :). Va rog, mai am nevoie de un pic de ajutor de la voi.
Cum stau acum: m-am folosit de sfaturile voastre si am un card focussat in interfata phoenix.

Normal http://sateliti.info/images/smilies/Comp_arunc.gif, nu reusesc sa vad vreun canal codat din grila focus. Nu mai zic nimic de sharing , eu vreau acum sa fac sa functioneaze cardul asta in phoenix. Mentionez ca in receptorul de la ei cardul este functional, deci nu e o problema cu el.

Am cules informatii despre ce si cum trebuie sa fac si:
-am instalat in receptor mbox ultima varianta, am pornit emu mbox+newcs, am pornit scriptul de serial+USB. Totul cum a descris snow in postul 14 de mai sus.
-am urcat cu ftp-ul fisierele postate de catre voi: (mbox.cfg, cwshare.cfg, add.data, 10110.list) in folderul var/keys si newcs.xml in folderul var/tuxbox/config. le-am setat la toate atibutul 755
-am instalat pe calculator mbox control center; am creat un profil, s-a conectat la receptor

Ce cred eu ca nu este in regula:
1.Motoru, spuneai intr-un post mai sus ca s-ar putea ca la cardul focussat sa difere frecventa cuartului. In newcs.xml postat de snow aceasta valoare este de 357. Ramane asa sau trebuie schimbata?
2.cand dau restart Mbox de la butonul din control center, in stanga jos scrie pasii pe care ii face. Se opreste cu eroare atunci cand se pare ca citeste mbox.cfg. Iata care este descrierea acestei erori:
===========
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.

For example:

<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>

When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
===========
3.In mbox control center are in meniu un tab numit "Newcs" si care deschide o forma ce iti ofera posibilitatea sa te conectezi, sau cel putin asa cred eu, la newcs. Ce setari trebuie in acele campuri?: IP-adress/DNS (eu am incercat si cu IP-ul receptorului(192.168.1.10) si cu 127.0.0.1 cel folosit, am vazut, in cwshare.cfg), Port(am incercat si cu 10110 si cu 14000), Password(am incercat si cu dummy si cu newcs si fara nimic). Mesajul dupa apasarea butonului "Connect" este invariabil acelasi: "Connection is forcefully rejected"
4.Din telnet la comanda mbox.sh40 iata ce se intampla:
=============
-sh-3.00# mbox.sh40
[12:21:04] STAPI INIT ... OK :)
[12:21:04] ExYuSAT Team http://www.exyusat.com , http://mbox.exyusat.com/index.php
[12:21:04] Starting MBOX version 0.4 BETA (build 0019) coded by The_Ripper
[12:21:04] This program is for educational & informational purposes only!!
[12:21:04] Donation to project: http://mbox.exyusat.com/donate.htm
[12:21:04] ===> Net Mode <===
[12:21:04] Reading cwshare.cfg ...
[12:21:04] Trying to get online,please wait ...
[12:21:04] Total 1 newcamd server(s) to connect
[12:21:04] Creating ecm parser thread ...OK
[12:21:04] Creating timer thread ...OK
[12:21:04] Creating newcamd worker thread ...OK
[12:21:04]
[12:21:04] ReReading pmt.tmp
[12:21:04] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...
[12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).
[12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).
[12:21:05] [newcamd] Trying to connect to newcamd server (127.0.0.1:10110)
[12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...
[12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).
[12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).
=============
Nu stiu, pare ca se conecteaza la interfata(Connected to (127.0.0.1:10110)) dar gaseste serverul oprit(... or server gone offline)!!

Din experineta voastra, aveti idee unde este buba (sau bubele)?

Multumesc pentru orice sfat,
Rocco

motoru
07-11-08, 23:23
357 e bun pt focus, la ora aceea nu ma informasem suficient cu frecventele, e absolut corect ce a scris snow.
Daca ai facut tot ce scrie acolo trebuie sa mearga !

important:
- in mbox.cfg D { 2 }
- in cwshare.cfg introduci linia C: { 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0B000000:0B000000;} si pui localul prioritar cu linia H: { 0B000000; }
-in 10110.list pui SF: { 0000 }

pt sharing(network mode) trebuie sa-ti pui linie M (host and pass)+hostIP+setare rooter, exista tutoriale pt asta.


daca nu te descurci iti trimit fis gata configurate.

rocco2007r
10-11-08, 16:02
Salut,

Va rog, ma poate ajuta cineva?
Nu reusesc sa "pornesc" cardul f___ss_t din phoenix, nu vad niciun canal codat.
In plus de postul meu de mai sus am constatat ca:
-daca pornesc din telnet mbox.sh40, incepe sa scrie in debug.txt din folderul temp: Iata ce imi apare atunci cand browsez pe canalele codate:
[00:01:46] ReReading pmt.tmp
[00:01:46] ==================================================================
[00:01:46] ECM: CA ID: 0x0B00 Conax -> CA PID: 0x011F
[00:01:46] ==================================================================
[00:01:49]
[00:01:49] ReReading pmt.tmp
[00:01:49] ==================================================================
[00:01:49] ECM: CA ID: 0x0B00 Conax -> CA PID: 0x012F
[00:01:49] ==================================================================

Cele 2 PID-uri de mai sus corespund la TVR1 si TVR2.

Ce concluzii trag de aici:
-scriptul de serial-usb este instalat corect
-cardul se simte, ca nu i-am spus nicaieri ca e conax
-ceva, ceva tot face configurarea mea mbox+newcs. dar...
-ce e insa gresit? newcs.xml, mbox.cfg, cwsare.cfg sau 10110.list?

Alte intrebari?
-pentru card conax, cazul meu, in newcs.xml linia "<!-- <boxkey>0000000000</boxkey> -->" trebuie decomentata sau nu? Si daca da, ce trebuie in loc de "0000000000"?
-nu mi-e foarte clar ce versiune de mbox ruleaza pe receptorul meu. De unde vad aceasta informatie? Eu ce-am facut: am luat ultima versiune de mbox, am copiat fisierele prin ftp in var/bin si am rulat din telnet fisierul mbox.sh40. E bine sau nu?

Multumesc,
Rocco

Snow
10-11-08, 16:15
foloseste newcs.xml-ul de aici
vezi ca-n var keys trebuie sa mai ai si newcamd.list
spune-mi ce ai in 10110.list

rocco2007r
10-11-08, 16:41
foloseste newcs.xml-ul de aici
vezi ca-n var keys trebuie sa mai ai si newcamd.list
spune-mi ce ai in 10110.list



Salut,

Eu acum sunt la job, diseara de abia astept sa pun in practica e ai spus.

Alte date:
-1. Undeva se pare ca mi-a scapat informatia cum ca ar fi trebuit si fiserul "newcamd.list". Asa e, nu il am, mersi ca ai observat. Am cautat acum pe forum si nu am gasit decat ceva mai vechi postat de otheitis:
#CWS_KEEPALIVE = 300
#CWS_INCOMING_PORT = 12000
CWS = 192.168.1.5 10110 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
CWS = 192.168.1.5 10111 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
#lan newcs

E bine?
-la mine, de fapt, IP-ul asta va fi 192.168.1.10
-textul abipbox e ok?
-2. newcs.xml atasat de tine acum difera de cel al meu(care este tot de la tine dintr-un post mai vechi) prin linia asta care e acum in plus: <autosid>no</autosid>. O sa-l modific in consecinta.
-3. 10110.list contine o singura linie, si anume:
SF: { 0000 }


Mersi mult snow,
rocco

otheitis
10-11-08, 16:47
CWS = 127.0.0.1 10110 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15
CWS = 127.0.0.1 10111 abipbox abipbox 01 02 03 04 05 06 07 08 09 10 11 12 13 15

Asa sa il pui....Eu am folosit pe ip care am avut la ipbox atunci.Cu asta o sa merge 100%
orice ip si sa ai pe ipbox.

rocco2007r
11-11-08, 13:49
Salut,

Am facut toate setarile in toate fisierele asa cum m-ati indrumat.
Din pacate nu reusesc nicicum sa pornesc tot mecanismul asta mbox+newcs+phoenix, pur si simplu nu se deschide niciun canal codat.
Va rog, ca sa ma linistesc si eu, imi poate raspunde cineva la aceste 3 nelamuriri?
Folosesc MBOX control center. Tool-ul asta(care arata foarte bine, pacat ca nu are si un help) imi indica 3 posibile probleme, si anume:
-1. in tab-ul telnet la comanda mbox.sh40 dupa linia in care se comunica faptul ca s-a conecatat la device ([12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...) lucrurile nu mai sunt ok. Mesajele sunt ([12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).) si ([12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).). Am cautat pe net dar numai o singura pagina imi gaseste pe google(numai ca e ceva adiacent despre o altfel de problema). Altceva ce nu inteleg este daca acest server de newcs trebuie pornit in mod explicit de undeva sau nu.
-2. daca dau restart MBOX de la butonul dreapta sus, dupa ce trece prin pasii(ii scrie in fereastra aplicatiei in bara de dialog din stanga jos) de connect ok, kill ok, la citirea mbox.cfg procesul crapa: mesajul de eroare este nespecific "An invalid argument was supplied" - pare ca e din .net framework - si aplicatia se inchide.
-3. in tabul newcs exista, sau asa pare, o metoda de conectare la serverul newcs. Orice configurare am facut pe IP, port, parola mesajul a fost invariabil acelasi: "Connection is forcefully rejected".

Rugamintea mea este sa imi confirmati sau nu daca aceste 3 chestii se intampla si la voi. Si daca stiti vreo solutie pentru ele.

Multumesc mult pentru orice sugestie,
rocco

eroler
11-11-08, 14:56
Incearca sa pui fisierele prin conectare ftp in fiecare director asa cum ti-am trimis im email .

livs
16-11-08, 19:37
Salut,

Am facut toate setarile in toate fisierele asa cum m-ati indrumat.
Din pacate nu reusesc nicicum sa pornesc tot mecanismul asta mbox+newcs+phoenix, pur si simplu nu se deschide niciun canal codat.
Va rog, ca sa ma linistesc si eu, imi poate raspunde cineva la aceste 3 nelamuriri?
Folosesc MBOX control center. Tool-ul asta(care arata foarte bine, pacat ca nu are si un help) imi indica 3 posibile probleme, si anume:
-1. in tab-ul telnet la comanda mbox.sh40 dupa linia in care se comunica faptul ca s-a conecatat la device ([12:21:05] [newcamd] Connected to (127.0.0.1:10110) ...) lucrurile nu mai sunt ok. Mesajele sunt ([12:21:05] [newcamd] Failed to read network stream or read time-out or server gone offline (127.0.0.1:10110).) si ([12:21:05] [newcamd] Login request was rejected (127.0.0.1:10110).). Am cautat pe net dar numai o singura pagina imi gaseste pe google(numai ca e ceva adiacent despre o altfel de problema). Altceva ce nu inteleg este daca acest server de newcs trebuie pornit in mod explicit de undeva sau nu.
-2. daca dau restart MBOX de la butonul dreapta sus, dupa ce trece prin pasii(ii scrie in fereastra aplicatiei in bara de dialog din stanga jos) de connect ok, kill ok, la citirea mbox.cfg procesul crapa: mesajul de eroare este nespecific "An invalid argument was supplied" - pare ca e din .net framework - si aplicatia se inchide.
-3. in tabul newcs exista, sau asa pare, o metoda de conectare la serverul newcs. Orice configurare am facut pe IP, port, parola mesajul a fost invariabil acelasi: "Connection is forcefully rejected".

Rugamintea mea este sa imi confirmati sau nu daca aceste 3 chestii se intampla si la voi. Si daca stiti vreo solutie pentru ele.

Multumesc mult pentru orice sugestie,
rocco

Am aceeasi problema, cu diferenta ca se conecteaza la newcs. Adica in mbox center imi apare ca logat la server.
DAr tot nu decodeaza cartela max.
Cum pot sa atasez fisiere, as vrea sa-mi verificati si mie configurile?

livs
29-11-08, 14:32
Cu chiu cu vai am reusit sa fac newcs-ul sa mearga.
Acum in mbox center vad cartela max cu un peer, dar care este offline.
Si tot nu decodeaza.
La newcs nu am nici un ecm - imi apare zero. Nu stiu daca e corect!
Imi pare ca mbox nu se conecteaza la newcs, chiar daca am linia c in cwshare.
Ce sa fac?

bz2ruebe
13-12-08, 17:24
merge la cineva conax cas7 cu phoenix ?

zildan
13-12-08, 22:26
Fii mai explicut, daca te referi la F@cus merge sigur.

bz2ruebe
14-12-08, 13:00
e hell@hd
merge cu mgcamd-newcs-usbrs232 ?
trebuie ceva configurat in plus ? ( img sifteam )
merci

zildan
14-12-08, 13:34
Cardul cred ca e imperecheat cu receptorul si il pui degeaba. Din cate stiu eu nu intra in share hell@hd.

bz2ruebe
14-12-08, 19:41
nu e imperechiat !

bz2ruebe
23-12-08, 20:50
Hi,

stie cineva ce se antampla aici ? In Smartmose/Phoenix am o cartela conax Hell@HD, asta se intampla la schimbat canale, de ex Nat. Geo HD selectat genereaza ultimele randuri.
Craciun fericit tuturor !!


Welcome to the NewCS console
[ 22:04:49 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 001A "Focus Sat - Antena 3 Romania [C]"
[ 22:04:50 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 001A "Focus Sat - Antena 3 Romania [C]"
[ 22:04:53 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 001A "Focus Sat - Antena 3 Romania [C]"
[ 22:04:55 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 001A "Focus Sat - Antena 3 Romania [C]"
[ 22:04:56 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 001A "Focus Sat - Antena 3 Romania [C]"
[ 22:05:12 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:13 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:16 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:18 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:21 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:23 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:24 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"
[ 22:05:27 ] [ Newcamd ] ECM local (NOT OK) 0B00 0000 0002 "TVTEL - RTP 2 [C]"

-minus
10-01-09, 00:20
Cum fac sa mearga CCcam 2011/NewCS162 cu -RS232 Card reader extern Pheonix,am tot cautat tutoriale dar..nimic!

bz2ruebe
12-01-09, 22:56
la mine merge ok cu newcs

rocco2007r
09-10-09, 16:00
Salut,

A venit toamna am sters de praf IPBOX-ul si m-am apucat iar de butonat.
De vreo 2 saptamani mi-a revenit cheful si am (re)citit tot ceea ce m-a interesat pe mine. Deci puteti sa ma criticati ca n-am inteles :| dar nu ca n-am citit :).
Care e tinta mea? Pai aceasi ca anul trecut cam pe vremea asta (cand am renuntat) si anume sa vad si eu ceva HD care nu e free. Chestia a devenit acum personala(ori eu ori ea:) )
Sa va reamintesc un pic cum a fost: si atunci am fost indrumat, normal, catre sharing. Si mi s-a explicat ca receptorul pe care tocmai il cumparasem nu-i de ajuns si ca trebuie si o interfata phoenix. am luat-o. si ca trebuie si un card activ de la un DTH ca asa este fair in sharing, daca vrei sa primesti trebuie sa dai ceva in schimb. Bun, deci l-am luat si pe asta. atunci am ales pachetul full ca sa am mai multe sanse(asa mi s-a explicat). acum am doar pachetul "familia" pentru ca intre timp, nemaifacand nimic si cum nici nu-mi trebuiau neparate canalele lor(ca am si cablu), am zis sa micsorez costurile.
Deci, incerc sa vad ca se face lumina si la mine cu sharingul. si, cum mbox+newcs mi s-a parut ca e mai pe intelesul meu, am purces la treaba.
Cum stau acum: am un IPBOX 900HD, imaginea NLB r10513, interfata Phoenix de la @gelvis, card f0cus activ(pachet familia acum), antena 115 pe montura H-H, internet fiberlink RDS, router, calculator si, nu in ultimul rand, mult chef :)
Pana la sharing insa, vreau sa vad ca macar pot sa activez cardul in interfata phoenix. adica mgcamd+newcs. bun. ei, acum e acum. teoretic eu cred ca am facut tot ce trebuie. insa, dezamagitor(normal pentru mine :) ), nu vrea si pace.
Ce cred eu ca e bine acum:
-newcs pare in regula. dovada sunt pozele de mai jos, printscreen-uri cu aproape toate paginile din consola(http://192.168.1.10:8080)
http://img117.imageshack.us/img117/8259/newcs8.th.jpg (http://img117.imageshack.us/i/newcs8.jpg/)
http://img134.imageshack.us/img134/6259/newcs9.th.jpg (http://img134.imageshack.us/i/newcs9.jpg/)
http://img117.imageshack.us/img117/4122/newcs7.th.jpg (http://img117.imageshack.us/i/newcs7.jpg/)
http://img59.imageshack.us/img59/2268/newcs6.th.jpg (http://img59.imageshack.us/i/newcs6.jpg/)
http://img207.imageshack.us/img207/4694/newcs5.th.jpg (http://img207.imageshack.us/i/newcs5.jpg/)
http://img180.imageshack.us/img180/351/newcs2.th.jpg (http://img180.imageshack.us/i/newcs2.jpg/)
http://img117.imageshack.us/img117/5200/newcs1.th.jpg (http://img117.imageshack.us/i/newcs1.jpg/)

Informatii in plus:
-cardul este activ, in receptorul original deschide canalele (sau cel putin facea asta acum 3 zile cand l-am mutat in phoenix).
-ma tot gandesc ca nu e bine configurat mg_cfg(am incercat mai multe variante luate de aici de pe forum, ultima varianta este asta). il reproduc mai jos. e ceva in neregula cu el?
---
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 00 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 00 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 06 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 00 }
---

si newcamd.list
---
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 10110
CWS = 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 10010 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
---

si 10110.list
---
SF: { 0000 }
---

Va rog, cu ce vreau sa ma ajutati:
1. daca imaginile de mai sus, imi confirma presupunerile: newcs lucreaza bine, inerfata este ok, conexiunea usb-serial de asemenea.
2. ce anume imi scapa, ce trebuie sa mai fac?
3. ce mijoc de verificare am ca mgcamd functioneaza bine sau nu?

Orice sfat este bine venit

Va multumesc,
Rocco

rocco2007r
19-10-09, 17:41
Salut,

S-a rezolvat problema de mai sus. Toate erau corecte, pur si simplu(si nu stiu cum) cardul se dezactivase. L-am reintrodus in receptorul pereche, l-am vazut ca si-a facut update la programe si am zis hopa, de aici e buba. Asa a fost, l-am bagat inapoi in phoenix si totul s-a luminat. In sfarsit!

Multumesc tuturor celor care m-au ajutat,
Rocco

P.S. Acum sa trecem la treburi serioase mbox+newcs. Peste ce-oi mai da si aici !!! Hai curaj...