DM 500HD - Procedura de incarcare a imaginilor

[Einstein]

Prin LAN cu browser:

1. Inchideti receptorul.
2. Apasa butonul frontal si tineti apasat pentru 10 secunde dupa ce l-ati reconectat la tensiune.
3. Conectare cu browser ca la DM 600

Prin miniUSB si LAN cu DreamUp 1.3.3.5:

DM 500HD nu are port serial, in schimb are miniUSB...

1. conectam portul miniUSB la un port USB al PC-ului
2. conectam cablul LAN
3. dechidem DreamUp si selectam COM-ul care apare (ex: COM15)
4. bifam "Network Connection" si setam IP-urile Dream-ului si ale PC
5. pornim receptorul
6. apasam "Flash"

[ibiza]

Ca o completare, pentru aflarea IP-ului pe care si-l aloca DM-ul de la serverul DHCP, daca nu exista acces la acest server, se pot parcurge pasii de mai jos.

1. Din Windows se afla adresa IP a calculatorului
Start -> Run -> cmd -> ipconfig

2. se da ping in adresa de broadcast (pentru adrese private de clasa C, aceasta este: 192.168.x.255

3. Se ruleaza:
arp-a

4. IP-ul DM-ului este pe aceiasi linie cu MAC-ul care incepe cu 00-09-34

Daca ai mai multe DM-uri si nu stii nici adresele IP ale celorlalte, le poti opri pentru cateva minute pe celelalte cat rulezi pasii de mai sus.

[valyp67]

Prin LAN cu browser:

1. Inchideti receptorul.
2. Apasa butonul frontal si tineti apasat pentru 10 secunde dupa ce l-ati reconectat la tensiune.
3. Conectare cu browser ca la DM 600

Prin miniUSB si LAN cu DreamUp 1.3.3.5:

DM 500HD nu are port serial, in schimb are miniUSB...

1. conectam portul miniUSB la un port USB al PC-ului
2. conectam cablul LAN
3. dechidem DreamUp si selectam COM-ul care apare (ex: COM15)
4. bifam "Network Connection" si setam IP-urile Dream-ului si ale PC
5. pornim receptorul
6. apasam "Flash"Multam frumos pentru acest minunat tutorial care e pe intelesul tuturor si m-a lamurit de am reusit prin acest miniUSB. Numai bine!

[Einstein]

DM500 HD Flashing firmware by Browser

Flashing a new firmware by Browser

What you need to flash
You need the image file you want to flash. Image files have the extension *.nfi. You can't flash other
images like *.img files. Don't try it - it won't work.
You need either a DHCP server and a configured bootloader
You need a browser and a network cable. Connect your Dreambox to a switch/hub/router in your lokal LAN.
To flash a new image, you can use the second stage loader. It must be present and not broken.
The following steps assume you have a DHCP server.
If you don't have one, you have to setup
 an IP address in the bootloader's serial setup.


- Power down the Dreambox, either using "shutdown" and by switching off by the power switch.
Standby is not enough!


- (1.) Press and hold the power button.
- (2.) Switch on your Dreambox.
- (3.) Your Dreambox will get the next free DHCP IP address from your router.


http://i39.tinypic.com/fna6gi.jpg


- Now, open a browser on your PC.
(1.) enter in the address line "http://ip/" .
- (2.) on the bottom of the page, there's a link called "firmware upgrade". Click it.


http://i39.tinypic.com/2uf4wlc.jpg


- On the next page, you can select the flash image you want to flash. be sure that it has the ".nfi" extension.
You can't flash other images (like .img)!
- Click on "FLASH!" and wait. It might take some time to upload and flash the image.
- Switch the box off again, and on again. The new image should be flashed and working.



---------- Post added at 22:12 ---------- Previous post was at 22:09 ----------

DM500 HD - manual IP

Setup a manual IP address in the bootloader:
OK, you don't have an DHCP server. That's normal if you don't have a router or configured one
by yourself. You don't need to install one, but you need to connect your Dreambox by a USB cable now.
You need to know which IP to give to your Dreambox. If you don't know which IP to choose, please ask
someone who can help you. You can choose any IP which is "near" your PC's IP address, but the 
IP should not be used by any other device.
For example, if your PC's IP is 192.168.0.5, you could use
192.168.0.10, unless another device already uses that. In that case, just choose 192.168.0.11, or whatever. It just needs to be in the 192.168.0.x range, where x is >= 1 and <= 254.
Start your favourite terminal program, for example HyperTerm. Setup your Comport to 115200/8N1.
 Press the "s" key.
Now a setup menu should appear. It should look similiar than the screenshot below.


http://i41.tinypic.com/95rnn9.jpg


Press the right arrow. You are now in the network setup menu.
Using "+" or "-" you can set the "Network type" to "manual".
Now you can enter an IP address in below. Press F9 to save your settings.
The Dreambox will shutdown.


http://i41.tinypic.com/1601ksi.jpg


Now go back and to the procedure again. "dhcp" shouldn't appear anymore, instead the IP you entered.


Sursa: http://tinyurl.com/yjh83rw